Datasheet
Table Of Contents
- Table 1. Device summary
- 1 Description
- Figure 1. M41T62 logic diagram
- Figure 2. M41T63 logic diagram
- Figure 3. M41T64 logic diagram
- Figure 4. M41T65 logic diagram
- Figure 5. M41T62 connections
- Figure 6. M41T63 connections
- Figure 7. M41T64 connections
- Figure 8. M41T65 connections
- Table 2. Signal names
- Figure 9. M41T62 block diagram
- Figure 10. M41T63 block diagram
- Figure 11. M41T64 block diagram
- Figure 12. M41T65 block diagram
- Figure 13. Hardware hookup for SuperCap™ backup operation
- 2 Operation
- 3 Clock operation
- 3.1 RTC registers
- 3.2 Calibrating the clock
- 3.3 Setting alarm clock registers
- 3.4 Watchdog timer
- 3.5 Watchdog output (WDO - M41T63/65 only)
- 3.6 Square wave output (M41T62/63/64)
- 3.7 Full-time 32 KHz square wave output (M41T64)
- 3.8 Century bits
- 3.9 Leap year
- 3.10 Output driver pin (M41T62/65)
- 3.11 Oscillator stop detection
- 3.12 Initial power-on defaults
- 4 Maximum ratings
- 5 DC and AC parameters
- Table 12. Operating and AC measurement conditions
- Figure 25. AC measurement I/O waveform
- Figure 26. Crystal isolation example
- Table 13. Capacitance
- Table 14. DC characteristics
- Table 15. Crystal electrical characteristics
- Table 16. Crystals suitable for use with M41T6x series RTCs
- Table 17. Oscillator characteristics
- Figure 27. Bus timing requirements sequence
- Table 18. AC characteristics
- 6 Package mechanical information
- Figure 28. QFN16 - 16-pin, quad, flat package, no-lead, 3 mm x 3 mm body size, outline
- Table 19. QFN16 - 16-pin, quad, flat package, no-lead, 3 mm x 3 mm body size, mechanical data
- Figure 29. QFN16 - 16-pin, quad, flat package, no-lead, 3 x 3 mm, recommended footprint
- Figure 30. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, outline
- Table 20. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, mechanical data
- Figure 31. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, recommended footprint
- Figure 32. Carrier tape for QFN16 3 mm x 3 mm package
- Table 21. Carrier tape dimensions for QFN16 3 mm x 3 mm package
- Figure 33. Carrier tape for LCC8 1.5 mm x 3.2 mm package
- Figure 34. Reel schematic
- Table 22. Reel dimensions for 12 mm carrier tape - QFN16 and LCC8 packages
- 7 Part numbering
- 8 Revision history
DC and AC parameters M41T62, M41T63, M41T64, M41T65
32/44 DocID10397 Rev 20
5 DC and AC parameters
This section summarizes the operating and measurement conditions, as well as the DC and
AC characteristics of the device. The parameters in the following DC and AC characteristic
tables are derived from tests performed under the measurement conditions listed in the
relevant tables. Designers should check that the operating conditions in their projects match
the measurement conditions when using the quoted parameters.
Figure 25. AC measurement I/O waveform
Figure 26. Crystal isolation example
Note: Substrate pad should be tied to V
SS
.
Table 12. Operating and AC measurement conditions
(1)
1. Output Hi-Z is defined as the point where data is no longer driven.
Parameter M41T6x
Supply voltage (V
CC
) 1.3 V to 4.4 V
Ambient operating temperature (T
A
) –40 to 85 °C
Load capacitance (C
L
) 50 pF
Input rise and fall times ≤ 5 ns
Input pulse voltages 0.2 V
CC
to 0.8 V
CC
Input and output timing ref. voltages 0.3 V
CC
to 0.7 V
CC
AI02568
0.8V
CC
0.2V
CC
0.7V
CC
0.3V
CC
AI09127
Crystal
XI
XO
GND
Local Grounding Plane
(Layer 2)