Datasheet
Table Of Contents
- Table 1. Device summary
- 1 Description
- Figure 1. M41T62 logic diagram
- Figure 2. M41T63 logic diagram
- Figure 3. M41T64 logic diagram
- Figure 4. M41T65 logic diagram
- Figure 5. M41T62 connections
- Figure 6. M41T63 connections
- Figure 7. M41T64 connections
- Figure 8. M41T65 connections
- Table 2. Signal names
- Figure 9. M41T62 block diagram
- Figure 10. M41T63 block diagram
- Figure 11. M41T64 block diagram
- Figure 12. M41T65 block diagram
- Figure 13. Hardware hookup for SuperCap™ backup operation
- 2 Operation
- 3 Clock operation
- 3.1 RTC registers
- 3.2 Calibrating the clock
- 3.3 Setting alarm clock registers
- 3.4 Watchdog timer
- 3.5 Watchdog output (WDO - M41T63/65 only)
- 3.6 Square wave output (M41T62/63/64)
- 3.7 Full-time 32 KHz square wave output (M41T64)
- 3.8 Century bits
- 3.9 Leap year
- 3.10 Output driver pin (M41T62/65)
- 3.11 Oscillator stop detection
- 3.12 Initial power-on defaults
- 4 Maximum ratings
- 5 DC and AC parameters
- Table 12. Operating and AC measurement conditions
- Figure 25. AC measurement I/O waveform
- Figure 26. Crystal isolation example
- Table 13. Capacitance
- Table 14. DC characteristics
- Table 15. Crystal electrical characteristics
- Table 16. Crystals suitable for use with M41T6x series RTCs
- Table 17. Oscillator characteristics
- Figure 27. Bus timing requirements sequence
- Table 18. AC characteristics
- 6 Package mechanical information
- Figure 28. QFN16 - 16-pin, quad, flat package, no-lead, 3 mm x 3 mm body size, outline
- Table 19. QFN16 - 16-pin, quad, flat package, no-lead, 3 mm x 3 mm body size, mechanical data
- Figure 29. QFN16 - 16-pin, quad, flat package, no-lead, 3 x 3 mm, recommended footprint
- Figure 30. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, outline
- Table 20. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, mechanical data
- Figure 31. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, recommended footprint
- Figure 32. Carrier tape for QFN16 3 mm x 3 mm package
- Table 21. Carrier tape dimensions for QFN16 3 mm x 3 mm package
- Figure 33. Carrier tape for LCC8 1.5 mm x 3.2 mm package
- Figure 34. Reel schematic
- Table 22. Reel dimensions for 12 mm carrier tape - QFN16 and LCC8 packages
- 7 Part numbering
- 8 Revision history
Clock operation M41T62, M41T63, M41T64, M41T65
28/44 DocID10397 Rev 20
3.6 Square wave output (M41T62/63/64)
The M41T62/63/64 offers the user a programmable square wave function which is output on
the SQW pin. RS3-RS0 bits located in 04h establish the square wave output frequency.
These frequencies are listed in Table 8. Once the selection of the SQW frequency has been
completed, the SQW pin can be turned on and off under software control with the square
wave enable bit (SQWE) located in register 0Ah.
The SQW output is an N-channel, open drain output driver for the M41T64, and a full CMOS
output driver for the M41T62/63. The initial power-up default for the SQW output is 32 KHz
(except for M41T64, which defaults disabled).
3.7 Full-time 32 KHz square wave output (M41T64)
The M41T64 offers the user a special 32 KHz square wave function which is enabled on
power-up to output on the F
32K
pin as long as V
CC
≥ 1.3 V, and the oscillator is running
(ST bit = '0'). This function is available within one second (typ) of initial power-up and can
only be disabled by setting the 32KE bit to '0' or the ST bit to '1.' If not used, the F
32K
pin
should be disconnected and allowed to float.
Table 8. Square wave output frequency
Square wave bits Square wave
RS3 RS2 RS1 RS0 Frequency Units
0000None–
0 0 0 1 32.768 kHz
00108.192kHz
00114.096kHz
01002.048kHz
01011.024kHz
0110512Hz
0111256Hz
1000128Hz
100164Hz
101032Hz
101116Hz
11008Hz
11014Hz
11102Hz
11111Hz