Datasheet
Table Of Contents
- Table 1. Device summary
- 1 Description
- Figure 1. M41T62 logic diagram
- Figure 2. M41T63 logic diagram
- Figure 3. M41T64 logic diagram
- Figure 4. M41T65 logic diagram
- Figure 5. M41T62 connections
- Figure 6. M41T63 connections
- Figure 7. M41T64 connections
- Figure 8. M41T65 connections
- Table 2. Signal names
- Figure 9. M41T62 block diagram
- Figure 10. M41T63 block diagram
- Figure 11. M41T64 block diagram
- Figure 12. M41T65 block diagram
- Figure 13. Hardware hookup for SuperCap™ backup operation
- 2 Operation
- 3 Clock operation
- 3.1 RTC registers
- 3.2 Calibrating the clock
- 3.3 Setting alarm clock registers
- 3.4 Watchdog timer
- 3.5 Watchdog output (WDO - M41T63/65 only)
- 3.6 Square wave output (M41T62/63/64)
- 3.7 Full-time 32 KHz square wave output (M41T64)
- 3.8 Century bits
- 3.9 Leap year
- 3.10 Output driver pin (M41T62/65)
- 3.11 Oscillator stop detection
- 3.12 Initial power-on defaults
- 4 Maximum ratings
- 5 DC and AC parameters
- Table 12. Operating and AC measurement conditions
- Figure 25. AC measurement I/O waveform
- Figure 26. Crystal isolation example
- Table 13. Capacitance
- Table 14. DC characteristics
- Table 15. Crystal electrical characteristics
- Table 16. Crystals suitable for use with M41T6x series RTCs
- Table 17. Oscillator characteristics
- Figure 27. Bus timing requirements sequence
- Table 18. AC characteristics
- 6 Package mechanical information
- Figure 28. QFN16 - 16-pin, quad, flat package, no-lead, 3 mm x 3 mm body size, outline
- Table 19. QFN16 - 16-pin, quad, flat package, no-lead, 3 mm x 3 mm body size, mechanical data
- Figure 29. QFN16 - 16-pin, quad, flat package, no-lead, 3 x 3 mm, recommended footprint
- Figure 30. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, outline
- Table 20. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, mechanical data
- Figure 31. LCC8 - 8-pin, 1.5 mm x 3.2 mm leadless chip carrier, recommended footprint
- Figure 32. Carrier tape for QFN16 3 mm x 3 mm package
- Table 21. Carrier tape dimensions for QFN16 3 mm x 3 mm package
- Figure 33. Carrier tape for LCC8 1.5 mm x 3.2 mm package
- Figure 34. Reel schematic
- Table 22. Reel dimensions for 12 mm carrier tape - QFN16 and LCC8 packages
- 7 Part numbering
- 8 Revision history
DocID10397 Rev 20 21/44
M41T62, M41T63, M41T64, M41T65 Clock operation
Keys:
0 = must be set to '0'
AF = alarm flag (read only)
BMB0 - BMB4 = watchdog multiplier bits
CB0-CB1 = century bits
OF = oscillator fail bit
RB0 - RB2 = watchdog resolution bits
RPT1-RPT5 = alarm repeat mode bits
RS0-RS3 = SQW frequency bits
S = sign bit
SQWE = square wave enable bit
ST = stop bit
WDF = watchdog flag bit (read only)
Table 4. M41T63 register map
Addr
Function/range BCD
format
D7 D6 D5 D4 D3 D2 D1 D0
00h 0.1 seconds 0.01 seconds
10ths/100ths
of seconds
00-99
01h ST 10 seconds Seconds Seconds 00-59
02h 0 10 minutes Minutes Minutes 00-59
03h 0 0 10 hours Hours (24-hour format) Hours 00-23
04h RS3 RS2 RS1 RS0 0 Day of week Day 01-7
05h 0 0 10 date Date: day of month Date 01-31
06h CB1 CB0 0 10M Month
Century/
month
0-3/01-12
07h 10 years Year Year 00-99
08h 0 0 S Calibration Calibration
09h RB2 BMB4 BMB3 BMB2 BMB1 BMB0 RB1 RB0 Watchdog
0Ah 0 SQWE 0 Al 10M Alarm month Al Month 01-12
0Bh RPT4 RPT5 AI 10 date Alarm date Al date 01-31
0Ch RPT3 0 AI 10 hour Alarm hour Al hour 00-23
0Dh RPT2 Alarm 10 minutes Alarm minutes Al min 00-59
0Eh RPT1 Alarm 10 seconds Alarm seconds Al sec 00-59
0FhWDFAF000OF00 Flags