Datasheet
Table Of Contents
- 1 Description
- 2 Signal description
- 3 Memory organization
- 4 Device operation
- 5 Instructions
- 6 Initial delivery state
- 7 Maximum rating
- 8 DC and AC parameters
- Table 5. Operating conditions (voltage range W)
- Table 6. Operating conditions (voltage range R)
- Table 7. Operating conditions (voltage range F, for devices identified by process letter T)
- Table 8. Operating conditions (voltage range F, for all other devices)
- Table 9. AC measurement conditions
- Figure 9. AC measurement I/O waveform
- Table 10. Input parameters
- Table 11. Cycling performance
- Table 12. Memory cell data retention
- Table 13. DC characteristics (M24C04-W, device grade 6)
- Table 14. DC characteristics (M24C04-R, device grade 6)
- Table 15. DC characteristics (M24C04-F device, grade 6 and grade 5)
- Table 16. 400 kHz AC characteristics
- Table 17. 100 kHz AC characteristics (I2C Standard mode)
- Figure 10. Maximum Rbus value versus bus parasitic capacitance (Cbus) for an I2C bus at maximum frequency fC = 400 kHz
- Figure 11. AC waveforms
- 9 Package mechanical data
- Figure 12. TSSOP8 – 8-lead thin shrink small outline, package outline
- Table 18. TSSOP8 – 8-lead thin shrink small outline, package mechanical data
- Figure 13. SO8N – 8-lead plastic small outline, 150 mils body width, package outline
- Table 19. SO8N – 8-lead plastic small outline, 150 mils body width, package data
- Figure 14. PDIP8 – 8-pin plastic DIP, 0.25 mm lead frame, package outline
- Table 20. PDIP8 – 8-pin plastic DIP, 0.25 mm lead frame, package mechanical data
- Figure 15. UFDFPN8 (MLP8) – package outline (UFDFPN: Ultra thin Fine pitch Dual Flat Package, No lead)
- Table 21. UFDFPN8 (MLP8) – package dimensions (UFDFPN: Ultra thin Fine pitch Dual Flat Package, No lead)
- 10 Part numbering
- 11 Revision history
Package mechanical data M24C04-W M24C04-R M24C04-F
30/34 DocID023994 Rev 3
Figure 14. PDIP8 – 8-pin plastic DIP, 0.25 mm lead frame, package outline
1. Drawing is not to scale.
2. Not recommended for new designs.
Table 20. PDIP8 – 8-pin plastic DIP, 0.25 mm lead frame, package mechanical data
Symbol
millimeters inches
(1)
1. Values in inches are converted from mm and rounded to four decimal digits.
Typ. Min. Max. Typ. Min. Max.
A – – 5.33 – – 0.2098
A1 – 0.38 – – 0.0150 –
A2 3.30 2.92 4.95 0.1299 0.1150 0.1949
b 0.46 0.36 0.56 0.0181 0.0142 0.0220
b2 1.52 1.14 1.78 0.0598 0.0449 0.0701
c 0.25 0.20 0.36 0.0098 0.0079 0.0142
D 9.27 9.02 10.16 0.3650 0.3551 0.4000
E 7.87 7.62 8.26 0.3098 0.3000 0.3252
E1 6.35 6.10 7.11 0.2500 0.2402 0.2799
e 2.54 – – 0.1000 – –
eA 7.62 – – 0.3000 – –
eB – – 10.92 – – 0.4299
L 3.30 2.92 3.81 0.1299 0.1150 0.1500
PDIP-B
A2
A1
A
L
be
D
E1
8
1
c
eA
b2
eB
E