Datasheet

ManualsBrandsSTMICROELECTRONICS ManualsLinear ICsLinear IC - Op-amp Multi-purpose TSSOP 8

This is information on a product in full production.

June 2013 DocID2163 Rev 11 1/22

LM158, LM258, LM358

Low-power dual operational amplifiers

Datasheet - production data

Features

• Internally frequency-compensated

• Large DC voltage gain: 100 dB

• Wide bandwidth (unity gain): 1.1 MHz

(temperature compensated)

• Very low supply current per operator

essentially independent of supply voltage

• Low input bias current: 20 nA

(temperature compensated)

• Low input offset voltage: 2 mV

• Low input offset current: 2 nA

• Input common-mode voltage range includes

negative rails

• Differential input voltage range equal to the

power supply voltage

• Large output voltage swing 0 V to (V

-1.5 V)

Description

These circuits consist of two independent, high-

gain, internally frequency-compensated op-amps,

specifically designed to operate from a single

power supply over a wide range of voltages. The

low-power supply drain is independent of the

magnitude of the power supply voltage.

Application areas include transducer amplifiers,

DC gain blocks and all the conventional op-amp

circuits, which can now be more easily

implemented in single power supply systems. For

example, these circuits can be directly supplied

with the standard +5

V, which is used in logic

systems and will easily provide the required

interface electronics with no additional power

supply.

In linear mode, the input common-mode voltage

range includes ground and the output voltage can

also swing to ground, even though operated from

only a single power supply voltage.

DIP8

(Plastic package)

SO8 and MiniSO8

(Plastic micropackage)

TSSOP8

(Thin shrink small outline package)

Pin connections

(Top view)

Out1

In1-

In1+

4Vcc-

Vcc+

Out2

In2-

5 In2+

DFN8 2 x 2 mm

(Plastic micropackage)

www.st.com

Summary of content (22 pages)

PAGE 1
LM158, LM258, LM358 Low-power dual operational amplifiers Datasheet - production data Features • Internally frequency-compensated • Large DC voltage gain: 100 dB • Wide bandwidth (unity gain): 1.
PAGE 2
Contents LM158, LM258, LM358 Contents 1 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Typical applications . . . . . . . . . . . . .
PAGE 3
LM158, LM258, LM358 1 Schematic diagram Schematic diagram Figure 1.
PAGE 4
Absolute maximum ratings 2 LM158, LM258, LM358 Absolute maximum ratings Table 1.
PAGE 5
LM158, LM258, LM358 3 Operating conditions Operating conditions Table 2. Operating conditions Symbol VCC Parameter Value Supply voltage Unit 3 to 30 (1) Vicm Common mode input voltage range Toper Operating free air temperature range LM158 LM258 LM358 VCC - -0.3 V + to VCC -1.5 -55 to +125 -40 to +105 0 to +70 V °C 1. When used in comparator, the functionality is guaranteed as long as at least one input remains within the operating common mode voltage range.
PAGE 6
Electrical characteristics 4 LM158, LM258, LM358 Electrical characteristics Table 3. Electrical characteristics for VCC+ = +5 V, VCC- = Ground, Vo = 1.4 V, Tamb = +25°C (unless otherwise specified) Symbol Vio Parameter Min. Input offset voltage (1) LM158A LM258A, LM358A LM158, LM258 LM358 Typ.
PAGE 7
LM158, LM258, LM358 Electrical characteristics Table 3. Electrical characteristics for VCC+ = +5 V, VCC- = Ground, Vo = 1.4 V, Tamb = +25°C (unless otherwise specified) (continued) Symbol Parameter CMR Common mode rejection ratio Rs £ 10 kW Tmin £ Tamb £ Tmax Isource Output current source VCC+ = +15 V, Vo = +2 V, Vid = +1 V Min. Typ. 70 60 85 20 40 Isink Output sink current VCC+ = +15 V, Vo = +2 V, Vid = -1 V VCC+ = +15 V, Vo = +0.
PAGE 8
Electrical characteristics LM158, LM258, LM358 Figure 2. Open-loop frequency response Figure 3. Large signal frequency response 140 20 100 k7 10 M7 0.1 MF 1 k7 VCC - 100 VO VI VCC/2 80 OUTPUT SWING (Vpp) VOLTAGE GAIN (dB) 120 + VCC = 30 V & -55°C Tamb +125°C 60 40 20 VCC = +10 to +15 V & -55°C Tamb +125°C 0 +15 V - VO VI 15 + +7 V 2 k7 10 5 0 1.0 10 100 1k 10k 100k 1M 10M 1k 10k FREQUENCY (Hz) 100k 1M FREQUENCY (Hz) Figure 4.
PAGE 9
LM158, LM258, LM358 Electrical characteristics Figure 9. Current limiting 8 90 VCC - 80 7 VO + VCC/2 6 5 OUTPUT CURRENT (mA) OUTPUT VOLTAGE REFERENCED TO VCC+ (V) Figure 8. Output voltage vs source current IO - 4 Independent of VCC 3 Tamb = + 25°C 2 1 IO 70 60 + 50 40 30 20 10 0 0.001 0.01 0.1 1 10 100 -55 -35 OUTPUT SOURCE CURRENT (mA) -15 5 25 45 65 85 105 125 TEMPERATURE °C Figure 10. Input voltage range Figure 11.
PAGE 10
Electrical characteristics LM158, LM258, LM358 Figure 15. Power supply rejection ratio POWER SUPPLY REJECTION RATIO (dB) Figure 14. Gain bandwidth product GAIN BANDWIDTH PRODUCT (MHz) 1.5 1.35 1.2 1.05 0.9 0.75 VCC = ± 15 V 0.6 0.45 0.3 0.15 0 -55 -35 -15 5 25 45 65 85 105 125 Figure 16. Common-mode rejection ratio COMMON MODE REJECTION RATIO (dB) 110 105 SVR 100 95 90 85 80 75 70 65 60 -55 -35 -15 5 25 45 65 85 105 125 TEMPERATURE (°C) TEMPERATURE (°C) Figure 17. Phase margin vs.
PAGE 11
LM158, LM258, LM358 5 Typical applications Typical applications Single supply voltage VCC = +5 VDC. Figure 18. AC-coupled inverting amplifier Rf 100k W R1 10kW 10k W 2VPP 0 eo RB 6.2kW R3 100kW eO 1/2 LM158 Co 1/2 LM158 eI ~ R2 VCC 100k W A V = 1 + R2 R1 (As shown A V = 101) Rf R1 (as shown A V = -10) +5V RL 10k W R2 1M W e O R1 10k W (V) CI AV= - Figure 19. Non-inverting DC amplifier C1 10mF 0 Figure 20.
PAGE 12
Typical applications LM158, LM258, LM358 Figure 24. Using symmetrical amplifiers to reduce input current I eI IB I IB 1/2 LM158 Figure 25. Low drift peak detector IB eo 2N 929 IB 1mF ZI IB 3MW C eI 0.001mF IB Input current compensation R1 100kW C1 330pF 1/2 LM158 R5 470kW R4 10MW 1/2 LM158 C2 R3 100kW 330 pF R6 470kW Vo 1/2 LM158 R7 100kW VCC R8 100kW 12/22 C3 10mF DocID2163 Rev 11 eo Zo 0.001mF IB 3R 3MW IB Figure 26.
PAGE 13
LM158, LM258, LM358 6 Package information Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark.
PAGE 14
Package information 6.1 LM158, LM258, LM358 DIP8 package information Figure 27. DIP8 package mechanical drawing Table 4. DIP8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 5.33 Max. 0.210 A1 0.38 0.015 A2 2.92 3.30 4.95 0.115 0.130 0.195 b 0.36 0.46 0.56 0.014 0.018 0.022 b2 1.14 1.52 1.78 0.045 0.060 0.070 c 0.20 0.25 0.36 0.008 0.010 0.014 D 9.02 9.27 10.16 0.355 0.365 0.400 E 7.62 7.87 8.26 0.300 0.310 0.325 E1 6.
PAGE 15
LM158, LM258, LM358 6.2 Package information SO8 package information Figure 28. SO8 package mechanical drawing Table 5. SO8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.75 0.069 A1 0.10 A2 1.25 b 0.28 0.48 0.011 0.019 c 0.17 0.23 0.007 0.010 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 0.25 Max. 0.004 0.010 0.049 1.27 0.050 h 0.25 0.50 0.010 0.
PAGE 16
Package information 6.3 LM158, LM258, LM358 MiniSO8 package information Figure 29. MiniSO8 package mechanical drawing Table 6. MiniSO8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.1 A1 0 A2 0.75 b Max. 0.043 0.15 0 0.95 0.030 0.22 0.40 0.009 0.016 c 0.08 0.23 0.003 0.009 D 2.80 3.00 3.20 0.11 0.118 0.126 E 4.65 4.90 5.15 0.183 0.193 0.203 E1 2.80 3.00 3.10 0.11 0.118 0.122 e L 0.85 0.65 0.40 0.60 0.006 0.033 0.
PAGE 17
LM158, LM258, LM358 6.4 Package information TSSOP8 package information Figure 30. TSSOP8 package mechanical drawing Table 7. TSSOP8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.2 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 1.05 0.031 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.008 D 2.90 3.00 3.10 0.114 0.118 0.122 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.177 e 1.00 0.65 k 0° L 0.45 0.
PAGE 18
Package information 6.5 LM158, LM258, LM358 DFN8 2 x 2 package mechanical data Figure 31. DFN8 2 x 2 package mechanical drawing Table 8. DFN8 2 x 2 x 0.6 mm package mechanical data (pitch 0.5 mm) Dimensions Ref. A Millimeters Min. Typ. Max. Min. Typ. Max. 0.51 0.55 0.60 0.020 0.022 0.024 A1 0.05 A3 0.002 0.15 0.006 b 0.18 0.25 0.30 0.007 0.010 0.012 D 1.85 2.00 2.15 0.073 0.079 0.085 D2 1.45 1.60 1.70 0.057 0.063 0.067 E 1.85 2.00 2.15 0.073 0.079 0.
PAGE 19
LM158, LM258, LM358 Package information Figure 32.
PAGE 20
Ordering information 7 LM158, LM258, LM358 Ordering information Table 9.
PAGE 21
LM158, LM258, LM358 8 Revision history Revision history Table 10. Document revision history Date Revision 01-Jul- 2003 1 First release. 02-Jan-2005 2 Rthja and Tj parameters added in AMR Table 1 on page 4. 01-Jul-2005 3 ESD protection inserted in Table 1 on page 4. 05-Oct-2006 4 Added Figure 17: Phase margin vs. capacitive load. 30-Nov-2006 5 Added missing ordering information. 25-Apr-2007 6 Removed LM158A, LM258A and LM358A from document title.
PAGE 22
LM158, LM258, LM358 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.