Datasheet
Table Of Contents
- Figure 1. Block diagram
- 1 Description
- 2 Maximum ratings
- 3 Pin connection
- 4 Electrical characteristics
- 5 Typical electrical performance
- Figure 3. IC consumption vs. VCC
- Figure 4. IC consumption vs. TJ
- Figure 5. VCC Zener voltage vs. TJ
- Figure 6. Startup and UVLO vs. TJ
- Figure 7. Feedback reference vs. TJ
- Figure 8. E/A output clamp levels vs. TJ
- Figure 9. UVLO saturation vs. TJ
- Figure 10. OVP levels vs. TJ
- Figure 11. Inductor saturation threshold vs. TJ
- Figure 12. Vcs clamp vs. TJ
- Figure 13. ZCD sink/source capability vs. TJ
- Figure 14. ZCD clamp level vs. TJ
- Figure 15. R discharge vs. TJ
- Figure 16. Line drop detection threshold vs. TJ
- Figure 17. VMULTpk - VVFF dropout vs. TJ
- Figure 18. PFC_OK threshold vs. TJ
- Figure 19. PFC_OK FFD threshold vs. TJ
- Figure 20. Multiplier characteristics at VFF = 1 V
- Figure 21. Multiplier characteristics at VFF = 3 V
- Figure 22. Multiplier gain vs. TJ
- Figure 23. Gate drive clamp vs. TJ
- Figure 24. Gate drive output saturation vs. TJ
- Figure 25. Delay to output vs. TJ
- Figure 26. Start-up timer period vs. TJ
- 6 Application information
- 7 Application examples and ideas
- Figure 34. Demonstration board EVL6564-100W, wide-range mains: electrical schematic
- Figure 35. L6564 100W TM PFC: compliance to EN61000-3-2 standard
- Figure 36. L6564 100W TM PFC: compliance to JEITA-MITI standard
- Figure 37. L6564 100 W TM PFC: input current waveform at 230 - 50 Hz - 100 W load
- Figure 38. L6564 100W TM PFC: input current waveform at 100 V - 50 Hz - 100 W load
- 8 Package mechanical data
- 9 Order codes
- 10 Revision history
DocID16202 Rev 5 33/33
L6564
33
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
ST PRODUCTS ARE NOT AUTHORIZED FOR USE IN WEAPONS. NOR ARE ST PRODUCTS DESIGNED OR AUTHORIZED FOR USE
IN: (A) SAFETY CRITICAL APPLICATIONS SUCH AS LIFE SUPPORTING, ACTIVE IMPLANTED DEVICES OR SYSTEMS WITH
PRODUCT FUNCTIONAL SAFETY REQUIREMENTS; (B) AERONAUTIC APPLICATIONS; (C) AUTOMOTIVE APPLICATIONS OR
ENVIRONMENTS, AND/OR (D) AEROSPACE APPLICATIONS OR ENVIRONMENTS. WHERE ST PRODUCTS ARE NOT DESIGNED
FOR SUCH USE, THE PURCHASER SHALL USE PRODUCTS AT PURCHASER’S SOLE RISK, EVEN IF ST HAS BEEN INFORMED IN
WRITING OF SUCH USAGE, UNLESS A PRODUCT IS EXPRESSLY DESIGNATED BY ST AS BEING INTENDED FOR “AUTOMOTIVE,
AUTOMOTIVE SAFETY OR MEDICAL” INDUSTRY DOMAINS ACCORDING TO ST PRODUCT DESIGN SPECIFICATIONS.
PRODUCTS FORMALLY ESCC, QML OR JAN QUALIFIED ARE DEEMED SUITABLE FOR USE IN AEROSPACE BY THE
CORRESPONDING GOVERNMENTAL AGENCY.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2013 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com