User Instructions

111
DEFRNLIT EN
0478 131 9954 C - EN
wire is routed along potential sudden
drops, a clearance of at least 1m must be
maintained between the perimeter wire
and the danger area for safety reasons.
Regularly inspect the area on which the
machine is to be used and remove any
sticks, stones, wires, bones and all other
foreign objects that could be thrown up by
the machine.
After installing the perimeter wire,
particularly remove all tools from the
mowing area. Broken or damaged fixing
pins must be removed from the lawn and
disposed of.
Regularly check the area to be mown for
uneven areas and level them out.
Never use the machine with damaged
safety devices or with safety devices
removed.
The switch and safety devices installed in
the machine must not be removed or
bypassed.
All faulty, worn or damaged parts must be
replaced before using the machine.
Replace any illegible or damaged danger
signs and warnings on the machine. Your
STIHL specialist has a supply of
replacement stickers and all the other
spare parts.
Before initial operation, it must be ensured
– that the machine is in good operational
condition. This means that the covers
and guards must be in place and in
good condition.
– that the docking station is in a safe
operating condition. Here, all covers
must be properly installed and be in
good condition.
– that the power supply unit has been
connected to a properly installed
socket.
– that the insulation of the electric cable
and the mains plug on the power supply
unit is in good condition.
– that the entire machine (housing, hood,
fastening elements, mowing blade,
blade shaft, etc.) is neither worn nor
damaged.
– that the mowing blade and the blade
fastening are in proper condition
(secure seating, damage, wear).
(Ö 16.3)
– that all screws, bolts, nuts and other
fastening elements are in place and
properly tightened. Tighten any loose
screws, bolts and nuts prior to initial
operation (observe tightening torques).
Carry out any necessary work or consult a
specialist dealer. STIHL recommends
STIHL specialist dealers.
6.7 Programming
Observe local regulations regarding
permitted operating times for gardening
power tools with motors and programme
the active times accordingly. (Ö 14.3)
In particular, programming must also be
adapted so that no children, spectators or
animals are in the area to be mown during
operation.
Changing the programming using the
iMOW® app in the case of the RMI 632 C,
RMI 632 PC models can result in activities
that will not be expected by other people.
Changes to the mowing plan must
therefore be communicated in advance to
all affected people.
The robotic mower must not operate at the
same time as a sprinkler system. Adapt
the programming accordingly.
Ensure that the correct date and the
correct time are set on the robotic mower.
Correct the settings if necessary. Incorrect
values may cause the robotic mower to
start up unintentionally.
6.8 During operation
Keep other persons, especially
children
and animals, out of the
danger area.
Never allow children to approach or play
with the robotic mower during operation.
Starting a mowing operation using the
iMOW® app in the case of the RMI 632 C,
RMI 632 PC models may not be expected
by third parties. Affected people must
therefore be notified in advance about
possible activity of the robotic mower.
Never allow the robotic mower to operate
unattended if you know that animals or
persons, particularly children, are in the
vicinity.
When operating the robotic mower in
public places, signs with the following
notice must be affixed around the mowing
area:
"Warning! Automatic lawn mower! Keep
away from the machine! Children must be
supervised!"
Caution – risk of injury!
Never put hands or feet on or
underneath rotating parts.
Never touch the rotating
blade.
Before thunderstorms, or if there is a
danger of lightning strikes, disconnect the
power supply unit from the mains. The
robotic mower must not be operated.