Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Maintenance, Repair and Storage
- 7 Before Starting Work
- 8 Assembling the Pressure Washer
- 9 Connecting the Water Supply
- 10 Ground Fault Circuit Interruptor (GFCI)
- 11 Switching the Pressure Washer On and Off
- 12 During Operation
- 13 After Finishing Work
- 14 Transporting
- 15 Storing
- 16 Cleaning
- 17 Inspection and Maintenance
- 18 Troubleshooting Guide
- 19 Specifications
- 20 Replacement Parts and Equipment
- 21 Disposal
- 22 Limited Warranty
- 23 Trademarks
- 24 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Mantenimiento, reparación y almacenamiento
- 7 Antes de empezar a trabajar
- 8 Armado de la hidrolavadora
- 9 Conexión del suministro de agua
- 10 Interruptor de pérdidas a tierra (GFCI)
- 11 Encendido y apagado de la hidrolavadora
- 12 Durante el funcionamiento
- 13 Después de completar el trabajo
- 14 Transporte
- 15 Almacenamiento
- 16 Limpieza
- 17 Inspección y mantenimiento
- 18 Guía de solución de problemas
- 19 Especificaciones
- 20 Piezas y equipos de repuesto
- 21 Eliminación
- 22 Garantía limitada
- 23 Marcas comerciales
- 24 Direcciones
0458-814-8621-A
30
English
16 Cleaning
When storing the pressure washer for three months or
longer:
► Clean the pressure washer, @ 16.1.
► Store the pressure washer indoors in a dry and secure
location, out of the reach of children and other
unauthorized persons.
► If the pressure washer cannot be stored in a room where
it is protected from freezing temperatures, protect the
pressure washer as outlined above, @ 13.2.
NOTICE
Freezing temperatures can damage components of the
pressure washer. STIHL recommends storing the pressure
washer indoors in a dry room where it is protected from
freezing temperatures. Relieve all system pressure and
make sure all water is eliminated from the pump system and
hoses before storing.
16.1 Cleaning the Pressure Washer
WARNING
Before carrying out any of the cleaning work specified in this
chapter @ 6, take certain measures to reduce the risk of
personal injury from unintended activation: switch off the
pressure washer and disconnect the unit from the power
supply. Relieve all system pressure by pulling the trigger
switch and lock the spray gun trigger.
To clean the pressure washer:
► Clean the pressure washer's polymer components,
couplings and connectors with a slightly dampened cloth.
Do not use abrasives or solvents that may damage the
pressure washer's polymer components.
► Do not use a pressure washer to clean the unit or
otherwise spray it with water or other liquids.
16.2 Cleaning the Nozzle and Spray Lance
A clogged high pressure nozzle can cause excessive
pressure to build in the pump. Clean the high-pressure
nozzle if it becomes clogged.
To clean the nozzle and spray lance:
► Rinse the nozzle and spray lance under running water and
dry them with a cloth.
► If the nozzle is blocked, use the cleaning needle to clear
the opening.
16 Cleaning
0000-GXX-4369-A0
0000-GXX-4370-A0