Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Kickback and Other Reactive Forces
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 The Chain Brake
- 13 Overload Cutout
- 14 Switching the Chain Saw On and Off
- 15 Checking the Chain Saw
- 16 After Finishing Work
- 17 Transporting
- 18 Storing
- 19 Cleaning
- 20 Inspection and Maintenance
- 21 Troubleshooting Guide
- 22 Specifications
- 23 Combinations of Guide Bars and Saw Chains
- 24 Replacement Parts and Equipment
- 25 Disposal
- 26 Limited Warranty
- 27 Trademarks
- 28 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Contragolpe y otras fuerzas reactivas
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 El freno de cadena
- 13 Disyuntor de sobrecarga
- 14 Encendido y apagado de la motosierra
- 15 Revisión de la motosierra
- 16 Después de completar el trabajo
- 17 Transporte
- 18 Almacenamiento
- 19 Limpieza
- 20 Inspección y mantenimiento
- 21 Guía de solución de problemas
- 22 Especificaciones
- 23 Combinaciones de espadas y cadenas de aserrado
- 24 Piezas y equipos de repuesto
- 25 Eliminación
- 26 Garantía limitada
- 27 Marcas comerciales
- 28 Direcciones
0458-729-8621-A
47
English
21 Troubleshooting Guide
21.1 Chain Saw
21 Troubleshooting Guide
Always disconnect the chain saw from the power supply before carrying out any inspection, cleaning or maintenance.
Condition Possible Cause Remedy
Chain saw cuts out during
operation.
The chain saw was accidentally disconnected
from the power supply.
► Reconnect the chain saw to the power
supply.
The GFCI has interrupted the electrical circuit. ► Reset the GFCI.
The electrical outlet is secured with less than
16 A.
► Use a properly secured power supply.
The overload cutout was activated. ► Clean the chain.
► Properly tension the chain.
► Reset the overload cutout.
► Switch the chain saw back on.
Chain saw does not start
when switched on.
The chain saw was accidentally disconnected
from the power supply.
► Reconnect the chain saw to the power
supply.
The GFCI has interrupted the electrical circuit. ► Reset the GFCI.
The electrical outlet is secured with less than
16 A.
► Use a properly secured power supply.
The chain brake is engaged. ► Disengage the chain brake.
► Switch the chain saw back on.
The chain is tensioned too tight. ► Properly tension the chain.
The guide bar sprocket is blocked. ► Spray the guide bar sprocket with resin
remover.
During sawing, the wood
smokes or smells burnt.
The chain is dull or improperly sharpened. ► Properly sharpen the chain.
Working technique is improper or the saw is
being mis-used.
► Obtain instruction on proper working
technique.
Insufficient bar and chain oil. ► Have the chain lubrication mechanism
checked by an authorized STIHL servicing
dealer.