Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Kickback and Other Reactive Forces
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Battery Safety
- 10 Maintenance, Repair and Storage
- 11 Before Starting Work
- 12 Charging the Battery
- 13 LED Diagnostics and Acoustic Signals
- 14 STIHL AR Backpack Battery
- 15 Assembling the Chain Saw
- 16 The Chain Brake
- 17 Inserting and Removing the Battery
- 18 Switching the Chain Saw On and Off
- 19 Checking the Chain Saw
- 20 After Finishing Work
- 21 Transporting the Chain Saw and Battery
- 22 Storing the Chain Saw and Battery
- 23 Cleaning
- 24 Inspection and Maintenance
- 25 Troubleshooting Guide
- 26 Specifications
- 27 Combinations of Guide Bars and Saw Chains
- 28 Replacement Parts and Equipment
- 29 Disposal
- 30 Limited Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta motorizada
- 5.6 Uso y cuidado de la herramienta con batería
- 5.7 Mantenimiento
- 5.8 Advertencias de seguridad generales para motosierras
- 5.9 Causas del contragolpe y medidas de prevención
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Contragolpe y otras fuerzas reactivas
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Seguridad de la batería
- 10 Mantenimiento, reparación y almacenamiento
- 11 Antes de empezar a trabajar
- 12 Carga de la batería
- 13 Diagnóstico por LED y señales acústicas
- 14 Batería de mochila STIHL AR
- 15 Armado de la motosierra
- 16 El freno de cadena
- 17 Colocación y extracción de la batería.
- 18 Encendido y apagado de la motosierra
- 19 Revisión de la motosierra
- 20 Después de completar el trabajo
- 21 Transporte de la motosierra y de la batería
- 22 Almacenamiento de la motosierra y de la batería
- 23 Limpieza
- 24 Inspección y mantenimiento
- 25 Guía de solución de problemas
- 26 Especificaciones
- 27 Combinaciones de espadas y cadenas de aserrado
- 28 Piezas y equipos de repuesto
- 29 Eliminación
- 30 Garantía limitada
- 31 Marcas comerciales
- 32 Direcciones
0458-795-8621-A
34
English
11 Before Starting Work
11.1 Preparing the Chain Saw for Operation
Before starting work:
► Fully charge the battery, @ 12.2.
► Mount the guide bar and saw chain, @ 15.2.1.
► Tension the chain, @ 15.3.
► Fill the chain oil tank, @ 15.4.2.
► Check the chain brake, @ 19.1.
► Check the controls for proper function and condition,
@ 19.2.
► Check the chain oil flow rate, @ 19.3.
12.1 Setting up the Charger
WARNING
Read and follow the safety precautions on the battery and
charger and all warnings and instructions that accompany
those products. To reduce the risk of short circuit, which
could lead to electric shock, fire and explosion, make sure
the charger and its components are dry and not damaged;
operate the charger indoors at an appropriate ambient
temperature.
WARNING
A typical household electric circuit is between 15 and 20
amps. A single STIHL AL 500 charger draws approximately
4.8 amps. A single AL 300 charger draws approximately
4.4 amps. To reduce the risk of fire from overloading an
electrical circuit:
► Ensure the electrical system is rated to withstand the
expected electrical draw before charging your battery.
► Charge multiple batteries one at a time or on separate
circuits, unless you know your circuit can handle the total
expected draw from multiple chargers.
WARNING
Since the charger heats up during the charging process, do
not operate the charger on a combustible surface or in a
location where combustible gases, liquids, vapors, dusts or
other materials and substances are present.
To set up the charger:
► Insert the plug (3) into a properly installed electrical
outlet (4) matching the voltage and electrical frequency
stated on the rating plate on the charger.
The charger runs a self-test immediately after it is plugged
in. The charger LED (1) will glow green for about 1 second,
then it will glow red briefly before going out. Once the LED
goes out, the self-test is complete and the charger is ready
to charge the battery.
11 Before Starting Work
12 Charging the Battery
3
2
0000-GXX-3228-A1
4
1