Instruction Manual
Table Of Contents
- STIHL MSA 161 T
- 1 Vorwort
- 2 Informationen zu dieser Gebrauchsanleitung
- 3 Übersicht
- 4 Sicherheitshinweise
- 5 Motorsäge einsatzbereit machen
- 6 Motorsäge zusammenbauen
- 7 Kettenbremse einlegen und lösen
- 8 Akku einsetzen und herausnehmen
- 9 Motorsäge einschalten und ausschalten
- 10 Motorsäge und Akku prüfen
- 11 Mit der Motorsäge arbeiten
- 12 Nach dem Arbeiten
- 13 Transportieren
- 14 Aufbewahren
- 15 Reinigen
- 16 Warten
- 17 Reparieren
- 18 Störungen beheben
- 19 Technische Daten
- 20 Kombinationen der Führungsschienen und Sägeketten
- 21 Ersatzteile und Zubehör
- 22 Entsorgen
- 23 EU-Konformitätserklärung
- 24 Anschriften
- 25 Allgemeine Sicherheitshinweise für Elektrowerkzeuge
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Overview
- 4 Safety Precautions
- 5 Preparing the Saw for Operation
- 6 Assembling the Saw
- 7 Engaging and Disengaging the Chain Brake
- 8 Removing and Fitting the Battery
- 9 Switching the Saw On/Off
- 10 Testing the Chain Saw and Battery
- 11 Operating the Saw
- 12 After Finishing Work
- 13 Transporting
- 14 Storing
- 15 Cleaning
- 16 Maintenance
- 17 Repairing
- 18 Troubleshooting
- 19 Specifications
- 20 Bar and Chain Combinations
- 21 Spare Parts and Accessories
- 22 Disposal
- 23 EC Declaration of Conformity
- 24 General Power Tool Safety Warnings
- 1 Préface
- 2 Informations concernant la présente Notice d'emploi
- 3 Vue d'ensemble
- 4 Prescriptions de sécurité
- 4.1 Symboles d'avertissement
- 4.2 Utilisation conforme à la destination prévue
- 4.3 Exigences posées à l'utilisateur
- 4.4 Vêtements et équipement
- 4.5 Aire de travail et voisinage
- 4.6 Bon état pour une utilisation en toute sécurité
- 4.7 Utilisation
- 4.8 Forces de réaction
- 4.9 Transport
- 4.10 Rangement
- 4.11 Nettoyage, entretien et réparation
- 5 Préparatifs avant l'utilisation de la tronçonneuse
- 6 Assemblage de la tronçonneuse
- 7 Serrage et desserrage du frein de chaîne
- 8 Introduction et extraction de la batterie
- 9 Mise en marche et arrêt de la tronçonneuse
- 10 Contrôle de la tronçonneuse et de la batterie
- 11 Travail avec la tronçonneuse
- 12 Après le travail
- 13 Transport
- 14 Rangement
- 15 Nettoyage
- 16 Maintenance
- 17 Réparation
- 18 Dépannage
- 19 Caractéristiques techniques
- 20 Combinaisons de guide-chaînes et de chaînes de tronçonneuse
- 21 Pièces de rechange et accessoires
- 22 Mise au rebut
- 23 Déclaration de conformité UE
- 24 Indications générales de sécurité pour outils électroportatifs
- 1 Premessa
- 2 Informazioni sulle presenti Istruzioni d’uso
- 3 Sommario
- 4 Avvertenze di sicurezza
- 5 Preparare la motosega per l'esercizio
- 6 Assemblaggio della motosega
- 7 Inserire e sbloccare il freno catena
- 8 Inserire e togliere la batteria
- 9 Accendere e spegnere la motosega
- 10 Controllo di motosega e batteria
- 11 Lavorare con la motosega
- 12 Dopo il lavoro
- 13 Trasporto
- 14 Conservazione
- 15 Pulizia
- 16 Manutenzione
- 17 Riparazione
- 18 Eliminazione dei guasti
- 19 Dati tecnici
- 20 Combinazioni di spranghe di guida e catene della sega
- 21 Ricambi e accessori
- 22 Smaltimento
- 23 Dichiarazione di conformità UE
- 24 Avvertenze di sicurezza generali per attrezzi elettrici
- 1 Voorwoord
- 2 Informatie met betrekking tot deze handleiding
- 3 Overzicht
- 4 Veiligheidsinstructies
- 5 Motorzaag klaarmaken voor gebruik
- 6 Motorzaag completeren
- 7 Kettingrem inschakelen en lossen
- 8 Accu aanbrengen en wegnemen
- 9 Motorzaag inschakelen en uitschakelen
- 10 Kettingzaag en accu controleren
- 11 Met de motorzaag werken
- 12 Na de werkzaamheden
- 13 Vervoeren
- 14 Opslaan
- 15 Reinigen
- 16 Onderhoud
- 17 Repareren
- 18 Storingen opheffen
- 19 Technische gegevens
- 20 Combinaties van zaagbladen en zaagkettingen
- 21 Onderdelen en toebehoren
- 22 Milieuverantwoord afvoeren
- 23 EU-conformiteitsverklaring
- 24 Algemene veiligheidswaarschuwingen voor elektrische gereedschappen
2
3
1
0000-GXX-2931-A0
1
► Place the oil tank cap in the filler opening so
that mark (1) lines up with mark (2).
► Press the oil tank cap down and rotate it clock‐
wise as far as it will go.
The oil tank cap snaps into place. The mark
(1) points to mark (3).
► Check to see if the oil tank cap can be pulled
upwards and off.
► If the oil tank cap cannot be pulled upwards
and off: Fold down the grip on the oil tank cap.
The oil tank is closed.
If the oil tank cap can be pulled upwards and off,
perform the following steps:
► Place the oil tank cap in the filler opening – in
any position.
1
0000-GXX-3135-A0
2
► Press the oil tank cap down and rotate it clock‐
wise as far as it will go.
► Press the oil tank cap down and rotate it coun‐
terclockwise until mark (1) points to mark (2).
► Now try again to close the oil tank.
► If the oil tank still cannot be closed properly:
Do not use the chainsaw and contact a STIHL
dealer for assistance.
The chainsaw is not in a safe condition.
6.4 Mounting the Spiked Bumper
0000-GXX-4445-A0
1
2
4
3
► Take out the screw (4) and remove the chain
catcher (3).
► Place the spiked bumper (1) in position.
► Fit the screw (2).
► Place the chain catcher (3) in position.
► Insert and tighten down the screw (4) firmly.
► Tighten down the screw (2) firmly.
7 Engaging and Disengaging
the Chain Brake
7.1 Engaging the Chain Brake
The saw is equipped with a chain brake.
The chain brake is activated by the inertia of the
front hand guard if the kickback force is high
enough or can be engaged by the operator.
0000-GXX-6240-A0
► Push the hand guard away from the handlebar
with your left hand.
The hand guard engages with an audible click.
The chain brake is engaged.
7.2 Disengaging the Chain Brake
0000-GXX-6241-A0
► Pull the hand guard back towards the handle
with your left hand.
The hand guard engages with an audible click.
The chain brake is disengaged.
8 Removing and Fitting the
Battery
8.1 Inserting the battery
► Engage the chain brake.
7 Engaging and Disengaging the Chain Brake English
0458-791-9621-C 37