Instruction Manual
Table Of Contents
- STIHL MSA 120 C, MSA 140 C
- 1 Vorwort
- 2 Informationen zu dieser Gebrauchsanleitung
- 3 Übersicht
- 4 Sicherheitshinweise
- 4.1 Warnsymbole
- 4.2 Bestimmungsgemäße Verwendung
- 4.3 Anforderungen an den Benutzer
- 4.4 Bekleidung und Ausstattung
- 4.5 Arbeitsbereich und Umgebung
- 4.6 Sicherheitsgerechter Zustand
- 4.7 Arbeiten
- 4.8 Reaktionskräfte
- 4.9 Laden
- 4.10 Elektrisch anschließen
- 4.11 Transportieren
- 4.12 Aufbewahren
- 4.13 Reinigen, Warten und Reparieren
- 5 Motorsäge einsatzbereit machen
- 6 Akku laden und LEDs
- 7 Motorsäge zusammenbauen
- 8 Kettenbremse einlegen und lösen
- 9 Akku einsetzen und herausnehmen
- 10 Motorsäge einschalten und ausschalten
- 11 Motorsäge und Akku prüfen
- 12 Mit der Motorsäge arbeiten
- 13 Nach dem Arbeiten
- 14 Transportieren
- 15 Aufbewahren
- 16 Reinigen
- 17 Warten
- 18 Reparieren
- 19 Störungen beheben
- 20 Technische Daten
- 21 Kombinationen der Führungsschienen und Sägeketten
- 22 Ersatzteile und Zubehör
- 23 Entsorgen
- 24 EU-Konformitätserklärung
- 25 Anschriften
- 26 Allgemeine Sicherheitshinweise für Elektrowerkzeuge
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Overview
- 4 Safety Precautions
- 5 Preparing the Saw for Operation
- 6 Charging the Battery, LEDs
- 7 Assembling the Saw
- 8 Engaging and Disengaging the Chain Brake
- 9 Removing and Fitting the Battery
- 10 Switching the Saw On/Off
- 11 Testing the Chain Saw and Battery
- 12 Operating the Saw
- 13 After Finishing Work
- 14 Transporting
- 15 Storing
- 16 Cleaning
- 17 Maintenance
- 18 Repairing
- 19 Troubleshooting
- 20 Specifications
- 21 Bar and Chain Combinations
- 22 Spare Parts and Accessories
- 23 Disposal
- 24 EC Declaration of Conformity
- 25 General Power Tool Safety Warnings
- 1 Préface
- 2 Informations concernant la présente Notice d'emploi
- 3 Vue d'ensemble
- 4 Prescriptions de sécurité
- 4.1 Symboles d'avertissement
- 4.2 Utilisation conforme à la destination prévue
- 4.3 Exigences posées à l'utilisateur
- 4.4 Vêtements et équipement
- 4.5 Aire de travail et voisinage
- 4.6 Bon état pour une utilisation en toute sécurité
- 4.7 Utilisation
- 4.8 Forces de réaction
- 4.9 Recharge
- 4.10 Branchement électrique
- 4.11 Transport
- 4.12 Rangement
- 4.13 Nettoyage, entretien et réparation
- 5 Préparatifs avant l'utilisation de la tronçonneuse
- 6 Recharge de la batterie et DEL
- 7 Assemblage de la tronçonneuse
- 8 Serrage et desserrage du frein de chaîne
- 9 Introduction et extraction de la batterie
- 10 Mise en marche et arrêt de la tronçonneuse
- 11 Contrôle de la tronçonneuse et de la batterie
- 12 Travail avec la tronçonneuse
- 13 Après le travail
- 14 Transport
- 15 Rangement
- 16 Nettoyage
- 17 Maintenance
- 18 Réparation
- 19 Dépannage
- 20 Caractéristiques techniques
- 21 Combinaisons de guide-chaînes et de chaînes de tronçonneuse
- 22 Pièces de rechange et accessoires
- 23 Mise au rebut
- 24 Déclaration de conformité UE
- 25 Indications générales de sécurité pour outils électroportatifs
- 25.1 Introduction
- 25.2 Sécurité à l'endroit de travail
- 25.3 Sécurité sur le plan électrique
- 25.4 Sécurité des personnes
- 25.5 Utilisation et emploi soigneux d'outils électroportatifs
- 25.6 Utilisation et emploi soigneux d'outils électroportatifs sans fil
- 25.7 Service après-vente
- 25.8 Consignes de sécurité applicables aux scies à chaîne / tronçonneuses
- 25.9 Causes d'un rebond, et comment les éviter
- 1 Premessa
- 2 Informazioni sulle presenti Istruzioni d’uso
- 3 Sommario
- 4 Avvertenze di sicurezza
- 4.1 Simboli di avvertimento
- 4.2 Impiego secondo la destinazione
- 4.3 Requisiti dell'utente
- 4.4 Abbigliamento ed equipaggiamento
- 4.5 Zona di lavoro e area circostante
- 4.6 Condizioni di sicurezza
- 4.7 Impiego
- 4.8 Forze di reazione
- 4.9 Carica
- 4.10 Collegamento elettrico
- 4.11 Trasporto
- 4.12 Conservazione
- 4.13 Pulizia, manutenzione e riparazione
- 5 Preparare la motosega per l'esercizio
- 6 Carica della batteria e LED
- 7 Assemblaggio della motosega
- 8 Inserire e sbloccare il freno catena
- 9 Inserire e togliere la batteria
- 10 Accendere e spegnere la motosega
- 11 Controllo di motosega e batteria
- 12 Lavorare con la motosega
- 13 Dopo il lavoro
- 14 Trasporto
- 15 Conservazione
- 16 Pulizia
- 17 Manutenzione
- 18 Riparazione
- 19 Eliminazione dei guasti
- 20 Dati tecnici
- 21 Combinazioni di spranghe di guida e catene della sega
- 22 Ricambi e accessori
- 23 Smaltimento
- 24 Dichiarazione di conformità UE
- 25 Avvertenze di sicurezza generali per attrezzi elettrici
- 25.1 Introduzione
- 25.2 Sicurezza sul posto di lavoro
- 25.3 Sicurezza elettrica
- 25.4 Sicurezza delle persone
- 25.5 Impiego e maneggio dell’attrezzo elettrico
- 25.6 Impiego e trattamento dell’attrezzo a batteria
- 25.7 Assistenza
- 25.8 Avvertenze di sicurezza per le seghe a catena
- 25.9 Cause e prevenzione del rimbalzo
- 1 Voorwoord
- 2 Informatie met betrekking tot deze handleiding
- 3 Overzicht
- 4 Veiligheidsinstructies
- 5 Motorzaag klaarmaken voor gebruik
- 6 Accu laden en leds
- 7 Motorzaag completeren
- 8 Kettingrem inschakelen en lossen
- 9 Accu aanbrengen en wegnemen
- 10 Motorzaag inschakelen en uitschakelen
- 11 Kettingzaag en accu controleren
- 12 Met de motorzaag werken
- 13 Na de werkzaamheden
- 14 Vervoeren
- 15 Opslaan
- 16 Reinigen
- 17 Onderhoud
- 18 Repareren
- 19 Storingen opheffen
- 20 Technische gegevens
- 21 Combinaties van zaagbladen en zaagkettingen
- 22 Onderdelen en toebehoren
- 23 Milieuverantwoord afvoeren
- 24 EU-conformiteitsverklaring
- 25 Algemene veiligheidswaarschuwingen voor elektrische gereedschappen
- 25.1 Inleiding
- 25.2 Veiligheid op de werkplek
- 25.3 Elektrische veiligheid
- 25.4 Veiligheid van personen
- 25.5 Gebruik en behandeling van het elektrische gereedschap
- 25.6 Gebruik en behandeling van het accugereedschap
- 25.7 Service
- 25.8 Veiligheidsinstructies voor kettingzagen
- 25.9 Oorzaak en voorkomen van een terugslag
► Never bridge the charger's contacts with
metallic objects (short circuit).
► Do not open the charger.
4.7 Working
4.7.1 Cutting
WARNING
■ Always work within calling distance of others
in case help is needed.
► Make sure than persons outside the work
area are within calling distance.
■ The user cannot concentrate on the work in
certain situations. The user can lose control of
the saw, stumble or fall and be seriously
injured.
►
Work calmly and carefully.
► If light and visibility are poor: Do not use
your saw.
► Operate the chainsaw alone.
► Do not work above shoulder height.
► Watch out for obstacles.
► Stand on the ground while working and
keep a good balance. If it is necessary to
work at heights: Use a lift bucket or a safe
platform.
►
If you begin to feel tired: Take a break.
■ The rotating saw chain can cut the operator.
This can result in serious injuries.
► Do not touch the rotating saw chain.
► If the saw chain is blocked by an object:
Switch off the chainsaw, engage the chain
brake and remove the battery. Then
remove the object causing the blockage.
■
The rotating chain becomes hot and expands.
If the chain is not lubricated sufficiently or not
re-tensioned at regular intervals, it may come
off the guide bar or break. This can result in
serious injuries and damage to property.
►
Use special chain oil.
► Check oil level in tank regularly during cut‐
ting work. Before the oil tank runs empty:
Fill up with chain oil.
►
Check chain tension regularly during cutting
work. If chain tension is insufficient: Ten‐
sion the chain.
■
If the behavior of the saw changes during
operation or feels unusual, it may no longer be
in a safe condition. This can result in serious
injuries and damage to property.
►
Stop work, remove the battery and contact
your STIHL servicing dealer for assistance.
■ Saw vibrations may occur during operation.
► Wear gloves.
► Take regular breaks.
► If signs of circulation problems occur: Seek
medical advice.
■ Sparks may occur if the rotating chain makes
contact with a hard object. Sparks may cause
a fire in an easily combustible location. This
can result in serious or fatal injuries and dam‐
age to property.
►
Do not work in an easily combustible loca‐
tion.
■ Note that the saw chain continues to rotate for
a short period after you release the trigger.
The rotating saw chain can cut the user. This
can result in serious injuries.
►
Wait for the chain to come to a standstill.
WARNING
0000-GXX-1245-A0
1
2
1
2
■
The guide bar can be pinched when cutting
wood that is under tension. The user can lose
control of the saw and be seriously injured.
►
Make a relieving cut in the compression
side (1) first, then perform bucking cut at
the tension side (2).
DANGER
■
Working near live electric cables can result in
accidental contact with the chain and damage
the cables. This can result in serious or fatal
injuries.
►
Do not work near live electric cables.
4.7.2 Limbing
WARNING
■
If the underside of the felled tree is limbed
first, it will no longer be supported on the
ground by branches. The tree can move dur‐
ing cutting work. This can result in serious or
fatal injuries.
►
Cut through large limbs on the underside of
the tree only after it has been bucked.
► Do not stand on the log while limbing it.
■ A branch may fall to the ground during limbing.
The user may trip, fall or be seriously injured.
► Limb from the base to the crown of the tree.
English 4 Safety Precautions
42 0458-716-9621-D