Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Kickback and Other Reactive Forces
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Battery Safety
- 10 Charger Safety
- 11 Maintenance, Repair and Storage
- 12 Before Starting Work
- 13 Charging the Battery
- 14 LED Diagnostics
- 15 Assembling the Chain Saw
- 16 The Chain Brake
- 17 Inserting and Removing the Battery
- 18 Switching the Chain Saw On and Off
- 19 Checking the Chain Saw
- 20 After Finishing Work
- 21 Transporting the Chain Saw and Battery
- 22 Storing the Chain Saw, Battery and Charger
- 23 Cleaning
- 24 Inspection and Maintenance
- 25 Troubleshooting Guide
- 26 Specifications
- 27 Combinations of Guide Bars and Saw Chains
- 28 Replacement Parts and Equipment
- 29 Disposal
- 30 Limited Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta eléctrica
- 5.6 Uso y cuidado de la herramienta de baterías
- 5.7 Mantenimiento
- 5.8 Advertencias de seguridad generales para motosierras
- 5.9 Causas del contragolpe y medidas de prevención
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Contragolpe y otras fuerzas reactivas
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Seguridad de la batería
- 10 Seguridad del cargador
- 11 Mantenimiento, reparación y almacenamiento
- 12 Antes de empezar a trabajar
- 13 Carga de la batería
- 14 Diagnóstico de LED
- 15 Armado de la motosierra
- 16 El freno de cadena
- 17 Colocación y extracción de la batería.
- 18 Encendido y apagado de la motosierra
- 19 Revisión de la motosierra
- 20 Después de completar el trabajo
- 21 Transporte de la motosierra y de la batería
- 22 Almacenamiento de la motosierra, de la batería y del cargador
- 23 Limpieza
- 24 Inspección y mantenimiento
- 25 Guía de solución de problemas
- 26 Especificaciones
- 26.1 STIHL MSA 120 C, MSA 140 C
- 26.2 Piñones de cadena
- 26.3 Profundidad de ranura mínima para las espadas
- 26.4 Ajuste de calibrador de profundidad
- 26.5 Batería STIHL serie AK
- 26.6 STIHL AL 101
- 26.7 Símbolos de la motosierra, de la batería y del cargador
- 26.8 Mejoramientos técnicos
- 26.9 Declaración de cumplimiento con norma FCC 15
- 27 Combinaciones de espadas y cadenas de aserrado
- 28 Piezas y equipos de repuesto
- 29 Eliminación
- 30 Garantía limitada
- 31 Marcas comerciales
- 32 Direcciones
0458-716-8621-E
60
English
27 Combinations of Guide Bars and Saw Chains
27.1 STIHL MSA 120 C, MSA 140 C
The guide bar and chain combinations listed above meet the
45° computed kickback angle requirement of UL 60745-2-13
when used on this model chain saw with the matching chain
sprocket listed above.
Use replacement guide bars or chains only as listed above
or as listed elsewhere by STIHL as conforming with the 45°
computed kickback angle requirement of UL 60745-2-13
when used on this model chain saw.
The listed guide bars are green-labeled reduced kickback
STIHL guide bars. The listed chains are green-labeled low
kickback STIHL chains
Since new bar/chain combinations may be developed after
publication of this manual, ask your authorized STIHL
servicing dealer for the latest STIHL recommendations.
27 Combinations of Guide Bars and Saw Chains
Pitch Drive link gauge/
Groove width
Length Guide bar Number of teeth
of sprocket nose
Drive link
count
Saw chain
1/4“ P
0.043 in.
(1.1 mm)
10 in.
(25 cm)
Rollomatic E Mini
8
56
71 PM3 (Type 3670)
12 in.
(30 cm)
Rollomatic E Mini 64