Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Kickback and Other Reactive Forces
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Battery Safety
- 10 Charger Safety
- 11 Maintenance, Repair and Storage
- 12 Before Starting Work
- 13 Charging the Battery
- 14 LED Diagnostics
- 15 Assembling the Chain Saw
- 16 The Chain Brake
- 17 Inserting and Removing the Battery
- 18 Switching the Chain Saw On and Off
- 19 Checking the Chain Saw
- 20 After Finishing Work
- 21 Transporting the Chain Saw and Battery
- 22 Storing the Chain Saw, Battery and Charger
- 23 Cleaning
- 24 Inspection and Maintenance
- 25 Troubleshooting Guide
- 26 Specifications
- 27 Combinations of Guide Bars and Saw Chains
- 28 Replacement Parts and Equipment
- 29 Disposal
- 30 Limited Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta eléctrica
- 5.6 Uso y cuidado de la herramienta de baterías
- 5.7 Mantenimiento
- 5.8 Advertencias de seguridad generales para motosierras
- 5.9 Causas del contragolpe y medidas de prevención
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Contragolpe y otras fuerzas reactivas
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Seguridad de la batería
- 10 Seguridad del cargador
- 11 Mantenimiento, reparación y almacenamiento
- 12 Antes de empezar a trabajar
- 13 Carga de la batería
- 14 Diagnóstico de LED
- 15 Armado de la motosierra
- 16 El freno de cadena
- 17 Colocación y extracción de la batería.
- 18 Encendido y apagado de la motosierra
- 19 Revisión de la motosierra
- 20 Después de completar el trabajo
- 21 Transporte de la motosierra y de la batería
- 22 Almacenamiento de la motosierra, de la batería y del cargador
- 23 Limpieza
- 24 Inspección y mantenimiento
- 25 Guía de solución de problemas
- 26 Especificaciones
- 26.1 STIHL MSA 120 C, MSA 140 C
- 26.2 Piñones de cadena
- 26.3 Profundidad de ranura mínima para las espadas
- 26.4 Ajuste de calibrador de profundidad
- 26.5 Batería STIHL serie AK
- 26.6 STIHL AL 101
- 26.7 Símbolos de la motosierra, de la batería y del cargador
- 26.8 Mejoramientos técnicos
- 26.9 Declaración de cumplimiento con norma FCC 15
- 27 Combinaciones de espadas y cadenas de aserrado
- 28 Piezas y equipos de repuesto
- 29 Eliminación
- 30 Garantía limitada
- 31 Marcas comerciales
- 32 Direcciones
0458-716-8621-E
54
English
24 Inspection and Maintenance
To properly lower the depth gauge:
► Lay the appropriate file gauge for the chain pitch on the
chain and press it against the cutter to be checked. If the
depth gauge protrudes past the file gauge, the depth
gauge must be filed down.
► File the depth gauge so that it is flush with the top of the
file gauge.
► Afterwards, remove the file gauge and file the leading
edge of the depth gauge parallel to the service mark.
When doing this, be careful not to further lower the highest
point of the depth gauge.
► Lay the file gauge on the chain to check the height of the
file gauge. The highest point of the depth gauge must be
flush with the top of the file gauge.
► After sharpening, clean the chain thoroughly, removing
any filings or grinding dust.
► Oil the chain thoroughly.
0000-GXX-1220-A1