Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Kickback and Other Reactive Forces
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Battery Safety
- 10 Charger Safety
- 11 Maintenance, Repair and Storage
- 12 Before Starting Work
- 13 Charging the Battery
- 14 LED Diagnostics
- 15 Assembling the Chain Saw
- 16 The Chain Brake
- 17 Inserting and Removing the Battery
- 18 Switching the Chain Saw On and Off
- 19 Checking the Chain Saw
- 20 After Finishing Work
- 21 Transporting the Chain Saw and Battery
- 22 Storing the Chain Saw, Battery and Charger
- 23 Cleaning
- 24 Inspection and Maintenance
- 25 Troubleshooting Guide
- 26 Specifications
- 27 Combinations of Guide Bars and Saw Chains
- 28 Replacement Parts and Equipment
- 29 Disposal
- 30 Limited Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta eléctrica
- 5.6 Uso y cuidado de la herramienta de baterías
- 5.7 Mantenimiento
- 5.8 Advertencias de seguridad generales para motosierras
- 5.9 Causas del contragolpe y medidas de prevención
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Contragolpe y otras fuerzas reactivas
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Seguridad de la batería
- 10 Seguridad del cargador
- 11 Mantenimiento, reparación y almacenamiento
- 12 Antes de empezar a trabajar
- 13 Carga de la batería
- 14 Diagnóstico de LED
- 15 Armado de la motosierra
- 16 El freno de cadena
- 17 Colocación y extracción de la batería.
- 18 Encendido y apagado de la motosierra
- 19 Revisión de la motosierra
- 20 Después de completar el trabajo
- 21 Transporte de la motosierra y de la batería
- 22 Almacenamiento de la motosierra, de la batería y del cargador
- 23 Limpieza
- 24 Inspección y mantenimiento
- 25 Guía de solución de problemas
- 26 Especificaciones
- 26.1 STIHL MSA 120 C, MSA 140 C
- 26.2 Piñones de cadena
- 26.3 Profundidad de ranura mínima para las espadas
- 26.4 Ajuste de calibrador de profundidad
- 26.5 Batería STIHL serie AK
- 26.6 STIHL AL 101
- 26.7 Símbolos de la motosierra, de la batería y del cargador
- 26.8 Mejoramientos técnicos
- 26.9 Declaración de cumplimiento con norma FCC 15
- 27 Combinaciones de espadas y cadenas de aserrado
- 28 Piezas y equipos de repuesto
- 29 Eliminación
- 30 Garantía limitada
- 31 Marcas comerciales
- 32 Direcciones
0458-716-8621-E
50
English
24 Inspection and Maintenance
To properly clean the guide bar and chain:
► Remove the guide bar and the chain, @ 15.2.2.
► Clean the oil outlet duct (1), oil inlet bore (2) and groove
(3) with a brush, a slightly dampened cloth or resin
solvent, such as STIHL Resin Remover & Lubricant. Do
not use detergents.
► Clean the chain with a brush, a slightly dampened cloth or
resin solvent. Do not use detergents.
► Do not use a pressure washer to clean the guide bar or
chain or otherwise spray them with water or other liquids.
24.1 Inspecting and Maintaining the Chain Saw
WARNING
To reduce the risk of personal injury from unintended
activation, remove the battery before inspecting the chain
saw or carrying out any maintenance, @ 11. Carry out only
the maintenance operations described in this manual. There
are no user-authorized repairs. STIHL recommends that
repair work be performed by authorized STIHL servicing
dealers.
Proper maintenance of the chain saw includes the following
activities:
► Inspecting the chain sprocket periodically and having a
worn chain sprocket replaced by an authorized STIHL
servicing dealer.
► Inspecting the guide bar for proper groove depth and
spread and replacing the guide bar it if it shows signs of
excessive wear or damage.
► Periodically sharpening the chain, maintaining the depth
limiting guides at the appropriate height and replacing the
saw chain when indicated by the relevant wear marks or
when the chain is damaged or shows signs of excessive
wear.
► Having worn, missing or damaged safety labels replaced
by an authorized STIHL servicing dealer.
If you make a warranty claim for a component which has not
been serviced or maintained properly, coverage may be
denied.
24.2 Inspecting and Maintaining the Chain Sprocket
► Switch off the chain saw, engage the chain brake and
remove the battery.
► Disengage the chain brake, @ 16.2.
► Remove the chain sprocket cover, saw chain and guide
bar.
► Check the chain sprocket cover for wear marks.
► If the wear marks are deeper than a = 0.020 in. (0.5 mm),
have the chain sprocket replaced.
24 Inspection and Maintenance
2
0000-GXX-1215-A0
3
3
1
a
0000-GXX-1216-A0