Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Assembling the Chain Saw
- 11 Lubricating the Saw Chain and Guide Bar
- 12 The Chain Brake
- 13 Mixing Fuel and Refueling the Chain Saw
- 14 Starting the Engine
- 15 Shutting Off the Engine
- 16 Checking the Chain Saw
- 17 Adjusting the Carburetor
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Combinations of Guide Bars and Saw Chains
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Emission Control Warranty
- 30 Trademarks
- 31 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Armado de la motosierra
- 11 Lubricación de la cadena de aserrado y de la espada
- 12 El freno de cadena
- 13 Mezcla del combustible y carga de combustible en la motosierra
- 14 Arranque del motor
- 15 Apagado del motor
- 16 Revisión de la motosierra
- 17 Ajuste del carburador
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de espadas y cadenas de aserrado
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Garantía del sistema de control de emisiones
- 30 Marcas comerciales
- 31 Direcciones
0458-759-8621-C
52
English
21 Cleaning
21.4 Cleaning the Spark Plug
WARNING
To reduce the risk of fire and burn injury, use only spark
plugs authorized by STIHL. Always press the spark plug
boot snugly onto the spark plug terminal.
WARNING
Do not use a spark plug with a detachable SAE adapter
terminal (1). Arcing may occur that could ignite combustible
fumes and cause a fire. This can result in serious injuries or
damage to property. Only use resistor type spark plugs with
solid, non-threaded terminals (2).
Using the wrong fuel mix (too much engine oil in the
gasoline), a dirty air filter, and unfavorable running
conditions (running for extended periods at partial throttle)
can affect the condition of the spark plug and cause deposits
to form on the insulator nose, degrading performance.
To clean the spark plug:
► Shut off the engine, @ 15.1.
► Engage the chain brake, @ 12.1.
► Allow the chain saw to cool down.
► Remove the filter cover (1).
► Remove the spark plug boot (2) by pulling the tab.
► Clean the area around the spark plug with a damp cloth or
soft brush.
► Unscrew the spark plug.
► Clean the spark plug with a damp cloth.
► If the spark plug is corroded, install a new spark plug.
► If damp, dry the spark plug thoroughly before re-inserting
it.
► Insert the spark plug and tighten it down firmly.
► Connect the spark plug boot (2) and press it down firmly.
► Mount the filter cover (1).
0000-GXX-1662-A0
1
2
2
1
0000-GXX-A379-A0
2
0000-GXX-A380-A0