Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Assembling the Chain Saw
- 11 Lubricating the Saw Chain and Guide Bar
- 12 The Chain Brake
- 13 Mixing Fuel and Refueling the Chain Saw
- 14 Starting the Engine
- 15 Shutting Off the Engine
- 16 Checking the Chain Saw
- 17 Adjusting the Carburetor
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Combinations of Guide Bars and Saw Chains
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Emission Control Warranty
- 30 Trademarks
- 31 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Armado de la motosierra
- 11 Lubricación de la cadena de aserrado y de la espada
- 12 El freno de cadena
- 13 Mezcla del combustible y carga de combustible en la motosierra
- 14 Arranque del motor
- 15 Apagado del motor
- 16 Revisión de la motosierra
- 17 Ajuste del carburador
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de espadas y cadenas de aserrado
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Garantía del sistema de control de emisiones
- 30 Marcas comerciales
- 31 Direcciones
0458-759-8621-C
45
English
16 Checking the Chain Saw
unauthorized use, shut off the engine, ensure the chain has
stopped and engage the chain brake before walking with the
saw or setting it down.
To shut off the engine:
► Release the throttle trigger (2) and throttle trigger
lockout (3).
► Move the Master Control Lever (1) to stop position .
The engine stops and the Master Control Lever (1)
springs back to position when released.
16.1 Checking the Operation of the Chain Brake
WARNING
Operating the saw with a missing, damaged, modified or
improperly maintained chain brake increases the risk of
severe or fatal injury from kickback. Never attempt to modify
or disable the chain brake. Never operate a saw if the chain
brake has been modified or does not function properly. If you
detect a change in the operating characteristics of the chain
brake, have your saw serviced immediately by an authorized
STIHL servicing dealer.
Before starting work, check the operation of the chain brake:
► Run the engine at idle speed.
► Engage the chain brake, @ 12.1.
► Accelerate up to full throttle for no more than 3 seconds.
A properly functioning chain brake prevents the chain from
rotating.
► If the chain brake fails to prevent the chain from rotating,
have the saw inspected and repaired by an authorized
STIHL servicing dealer.
16.2 Testing the Controls
Before starting work, confirm that the throttle trigger
lockout (1) and throttle trigger (2) are undamaged and
functioning properly.
Throttle Trigger Lockout (1) and Throttle Trigger (2)
WARNING
To reduce the risk of serious or fatal injuries, keep hands,
feet and other parts of the body away from the chain. Do not
touch the saw chain while the engine is running. Never touch
a moving chain with your hand or any part of your body,
@ 5.6.3. Keep bystanders out of the area while testing the
controls.
To test the controls:
► Shut off the engine, @ 15.
► Attempt to depress the throttle trigger.
If the trigger can be depressed without first depressing the
throttle trigger lockout, take the chain saw to an
authorized STIHL servicing dealer to be repaired before
use.
16 Checking the Chain Saw
2
3
0000-GXX-6457-A0
1
0000-GXX-1637-A0
2
1