Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Assembling the Chain Saw
- 11 Lubricating the Saw Chain and Guide Bar
- 12 The Chain Brake
- 13 Mixing Fuel and Refueling the Chain Saw
- 14 Starting the Engine
- 15 Shutting Off the Engine
- 16 Checking the Chain Saw
- 17 Adjusting the Carburetor
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Combinations of Guide Bars and Saw Chains
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Emission Control Warranty
- 30 Trademarks
- 31 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Armado de la motosierra
- 11 Lubricación de la cadena de aserrado y de la espada
- 12 El freno de cadena
- 13 Mezcla del combustible y carga de combustible en la motosierra
- 14 Arranque del motor
- 15 Apagado del motor
- 16 Revisión de la motosierra
- 17 Ajuste del carburador
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de espadas y cadenas de aserrado
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Garantía del sistema de control de emisiones
- 30 Marcas comerciales
- 31 Direcciones
0458-759-8621-C
48
English
18 After Finishing Work
17.4 Summer Operation
The shutter must be set to summer mode when working at
temperatures above 50 °F (10°C).
► Shut off the engine, @ 15.1.
► Engage the chain brake, @ 12.1.
► Remove the filter cover (1).
► Pull out the shutter (2).
► Re-insert the shutter (2) as shown above.
► Push the shutter (2) into the slots (3) until it stops.
The shutter (2) engages noticeably.
► Mount the filter cover (1).
18.1 Preparing for Transportation or Storage
WARNING
To reduce the risk of personal injury from unintended
activation or unauthorized use, shut off the engine and
engage the chain brake before transporting the chain saw or
putting it down. To reduce the risk of injuries from the sharp
cutters on the chain, always cover the guide bar with the
chain scabbard before transporting or storing the saw.
To prepare the saw for transportation or storage:
► Shut off the engine, @ 15.
► Release the chain brake and loosen the chain, @ 12.2.
► Re-engage the chain brake.
► Slide a chain scabbard over the guide bar so that it covers
the entire guide bar.
► Before using the saw, remember to re-tension the chain.
NOTICE
The chain contracts as it cools down. Failing to loosen the
chain after finishing work can damage the drive shaft and
bearings.
0000-GXX-A381-A0
1
2
0000-GXX-A384-A0
3
3
18 After Finishing Work