Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Emergency Situations
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 Lubricating the Saw Chain and Guide Bar
- 13 The Chain Brake
- 14 Mixing Fuel and Refueling the Chain Saw
- 15 Starting the Engine
- 16 Shutting Off the Engine
- 17 Checking the Chain Saw
- 18 Adjusting the Carburetor
- 19 After Finishing Work
- 20 Transporting
- 21 Storing
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 Combinations of Guide Bars and Saw Chains
- 27 Replacement Parts and Equipment
- 28 Disposal
- 29 Limited Warranty
- 30 Emission Control Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Situaciones de emergencia
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 Lubricación de la cadena de aserrado y de la espada
- 13 El freno de cadena
- 14 Mezcla del combustible y carga de combustible en la motosierra
- 15 Arranque del motor
- 16 Apagado del motor
- 17 Revisión de la motosierra
- 18 Ajuste del carburador
- 19 Después de completar el trabajo
- 20 Transporte
- 21 Almacenamiento
- 22 Limpieza
- 23 Inspección y mantenimiento
- 24 Guía de solución de problemas
- 25 Especificaciones
- 26 Combinaciones de espadas y cadenas de aserrado
- 27 Piezas y equipos de repuesto
- 28 Eliminación
- 29 Garantía limitada
- 30 Garantía del sistema de control de emisiones
- 31 Marcas comerciales
- 32 Direcciones
0458-787-8621-A
62
English
23 Inspection and Maintenance
WARNING
Depth gauges that are too low increase the potential and
force of kickback and other reactive forces, which can
increase the risk of serious personal injury. Always maintain
the proper distance (a) between the depth gauge and the top
of the cutter.
The depth gauge determines the depth to which the cutter
penetrates the wood and thus the chip thickness.
A depth gauge that is too low will increase the kickback
tendency of the chain saw and can increase kickback forces.
A depth gauge that is too high will prevent the cutter from
entering the workpiece and will lead to poor cutting
performance. Always keep the required distance (a)
between depth gauge and cutting edge, @ 25.5.
To properly lower the depth gauge:
► Lay the appropriate file gauge for the chain pitch on the
chain and press it against the cutter to be checked. If the
depth gauge protrudes past the file gauge, the depth
gauge must be filed down.
► File the depth gauge so that it is flush with the top of the
file gauge.
► Afterwards, remove the file gauge and file the leading
edge of the depth gauge parallel to the service mark.
When doing this, be careful not to further lower the highest
point of the depth gauge.
► Lay the file gauge on the chain to check the height of the
file gauge. The highest point of the depth gauge must be
flush with the top of the file gauge.
► After sharpening, clean the chain thoroughly, removing
any filings or grinding dust.
► Oil the chain thoroughly.
a
0000-GXX-1447-A0
0000-GXX-1220-A1