Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Emergency Situations
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 Lubricating the Saw Chain and Guide Bar
- 13 The Chain Brake
- 14 Mixing Fuel and Refueling the Chain Saw
- 15 Starting the Engine
- 16 Shutting Off the Engine
- 17 Checking the Chain Saw
- 18 Adjusting the Carburetor
- 19 After Finishing Work
- 20 Transporting
- 21 Storing
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 Combinations of Guide Bars and Saw Chains
- 27 Replacement Parts and Equipment
- 28 Disposal
- 29 Limited Warranty
- 30 Emission Control Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Situaciones de emergencia
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 Lubricación de la cadena de aserrado y de la espada
- 13 El freno de cadena
- 14 Mezcla del combustible y carga de combustible en la motosierra
- 15 Arranque del motor
- 16 Apagado del motor
- 17 Revisión de la motosierra
- 18 Ajuste del carburador
- 19 Después de completar el trabajo
- 20 Transporte
- 21 Almacenamiento
- 22 Limpieza
- 23 Inspección y mantenimiento
- 24 Guía de solución de problemas
- 25 Especificaciones
- 26 Combinaciones de espadas y cadenas de aserrado
- 27 Piezas y equipos de repuesto
- 28 Eliminación
- 29 Garantía limitada
- 30 Garantía del sistema de control de emisiones
- 31 Marcas comerciales
- 32 Direcciones
0458-787-8621-A
60
English
23 Inspection and Maintenance
STIHL chain is manufactured with wear marks to help the
operator identify excessive wear. The wear marks depicted
above (1 - 4) must remain visible.
► Replace the chain if any wear marks are no longer visible.
► Check the 30° sharpening angle of the cutters with a
STIHL file gauge matching the pitch of the chain.
► If the sharpening angle is incorrect, file the cutters to a 30°
angle.
► If you are unable to achieve the proper angle, or suspect
you have not achieved the proper angle, have the chain
sharpened by an authorized STIHL servicing dealer.
An improperly filed chain can be very dangerous. It can
increase the potential for reactive forces, including kickback,
and also increase the magnitude of those reactive forces.
The chain pitch marking (a) is embossed in the area of the
depth gauge of each cutter.
The markings mean the following:
Sharpening Saw Chain with Carbide-tipped Cutters
To sharpen the chain:
► Shut off the engine and engage the chain brake.
► Use the STIHL USG Chain Grinder with specialized wheel
for grinding carbide-tipped cutters.
Sharpening at varying or inconsistent angles or heights
can be very dangerous and may result in rough or uneven
running of the chain and increased wear, even to the point
of chain breakage. It also can increase the tendency and
force of kickback and other reactive forces.
► Grind all the right-handed cutters (4) cutters with the
following settings:
– Scale A: + 10°
–ScaleB: 0°
–ScaleC: +15°
► Grind all the left-handed cutters (1) cutters with the
following settings:
0000-GXX-1372-A0
1
2
3
4
a
0000-GXX-1446-A0
Marking (a) Saw Chain Pitch
11/4"
2 .325"
33/8"
4 .404"
6 3/8" PICCO
7 1/4" PICCO
4
0000-GXX-3488-A0
-
+
-
A
B
C
+
-
+
1 3 22