Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Emergency Situations
- 8 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Assembling the Chain Saw
- 12 Lubricating the Saw Chain and Guide Bar
- 13 The Chain Brake
- 14 Mixing Fuel and Refueling the Chain Saw
- 15 Starting the Engine
- 16 Shutting Off the Engine
- 17 Checking the Chain Saw
- 18 Adjusting the Carburetor
- 19 After Finishing Work
- 20 Transporting
- 21 Storing
- 22 Cleaning
- 23 Inspection and Maintenance
- 24 Troubleshooting Guide
- 25 Specifications
- 26 Combinations of Guide Bars and Saw Chains
- 27 Replacement Parts and Equipment
- 28 Disposal
- 29 Limited Warranty
- 30 Emission Control Warranty
- 31 Trademarks
- 32 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Situaciones de emergencia
- 8 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Armado de la motosierra
- 12 Lubricación de la cadena de aserrado y de la espada
- 13 El freno de cadena
- 14 Mezcla del combustible y carga de combustible en la motosierra
- 15 Arranque del motor
- 16 Apagado del motor
- 17 Revisión de la motosierra
- 18 Ajuste del carburador
- 19 Después de completar el trabajo
- 20 Transporte
- 21 Almacenamiento
- 22 Limpieza
- 23 Inspección y mantenimiento
- 24 Guía de solución de problemas
- 25 Especificaciones
- 26 Combinaciones de espadas y cadenas de aserrado
- 27 Piezas y equipos de repuesto
- 28 Eliminación
- 29 Garantía limitada
- 30 Garantía del sistema de control de emisiones
- 31 Marcas comerciales
- 32 Direcciones
0458-787-8621-A
39
English
11 Assembling the Chain Saw
► Fit the slider (3) over the guide (1).
► Screw on the quick-release (4) and tighten the screws (2).
► Pull the slider (3) forward as far as possible.
► Completely close the quick-release (4). The quick-release
must be positioned in the illustrated area (A).
The slider can no longer be moved.
11.4.2 Removing the Depth Limiter
To remove the depth limiter:
► Shut off the engine, @ 16.
► Engage the chain brake, @ 13.1.
► Open and unscrew the quick-release (1).
► Remove the slider (2).
► Remove the screws (4).
► Remove the guide (3).
11.5 Adjusting the Depth Limiter
The depth limiter can be adjusted depending on the
application. The setting of the depth limiter determines the
maximum entry depth of the guide bar into the material to be
cut. The cutting depth is adjustable from just a few
millimeters to approximately 8 in. (20 cm).
To adjust the depth limiter:
► Shut off the engine, @ 16.
► Engage the chain brake, @ 13.1.
0000-GXX-5872-A0
1
2
3
4
0000-GXX-5886-A0
3
4
A
2
3
1
0000-GXX-5887-A0
4
3
0000-GXX-3177-A0