Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Assembling the Chain Saw
- 11 Lubricating the Saw Chain and Guide Bar
- 12 The Chain Brake
- 13 Mixing Fuel and Refueling the Chain Saw
- 14 Starting the Engine
- 15 Shutting Off the Engine
- 16 Checking the Chain Saw
- 17 Adjusting the Carburetor
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Combinations of Guide Bars and Saw Chains
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Emission Control Warranty
- 30 Trademarks
- 31 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Armado de la motosierra
- 11 Lubricación de la cadena de aserrado y de la espada
- 12 El freno de cadena
- 13 Mezcla del combustible y carga de combustible en la motosierra
- 14 Arranque del motor
- 15 Apagado del motor
- 16 Revisión de la motosierra
- 17 Ajuste del carburador
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de espadas y cadenas de aserrado
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Garantía del sistema de control de emisiones
- 30 Marcas comerciales
- 31 Direcciones
0458-573-8621-D
65
English
25 Combinations of Guide Bars and Saw Chains
25.1 STIHL MS 261
The guide bar and chain combinations listed above meet the
45° computed kickback angle requirement of § 5.11 of
ANSI/OPEI B175.1 when used on this model chain saw with
the matching chain sprocket listed above.
Use replacement guide bars or chains only as listed above
or as listed elsewhere by STIHL as conforming with the 45°
computed kickback angle requirement of § 5.11 of
ANSI/OPEI B175.1 when used on this model chain saw.
The listed guide bars are green-labeled reduced kickback
STIHL guide bars. The listed chains are green-labeled low
kickback STIHL chains.
Since new bar/chain combinations may be developed after
publication of this manual, ask your authorized STIHL
servicing dealer for the latest STIHL recommendations.
25 Combinations of Guide Bars and Saw Chains
Pitch Drive link
gauge/Groove
width
Length Guide Bar Number of teeth
of sprocket nose
Drive link
count
Saw chain
.325"
0.063 in.
(1.6 mm)
16 in. (40 cm)
Rollomatic E 11
67
26 RM3
(Type 3634)
18 in. (45 cm) 74
20 in. (50 cm) 81