Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Assembling the Chain Saw
- 11 Lubricating the Saw Chain and Guide Bar
- 12 The Chain Brake
- 13 Mixing Fuel and Refueling the Chain Saw
- 14 Starting the Engine
- 15 Shutting Off the Engine
- 16 Checking the Chain Saw
- 17 Adjusting the Carburetor
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Combinations of Guide Bars and Saw Chains
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Emission Control Warranty
- 30 Trademarks
- 31 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Armado de la motosierra
- 11 Lubricación de la cadena de aserrado y de la espada
- 12 El freno de cadena
- 13 Mezcla del combustible y carga de combustible en la motosierra
- 14 Arranque del motor
- 15 Apagado del motor
- 16 Revisión de la motosierra
- 17 Ajuste del carburador
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de espadas y cadenas de aserrado
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Garantía del sistema de control de emisiones
- 30 Marcas comerciales
- 31 Direcciones
0458-573-8621-D
49
English
18 After Finishing Work
► Turn the low speed screw (L) a 1/4 of a turn
counter-clockwise.
► It is usually necessary to change the setting of the idle
speed screw (LA) after every correction to the low speed
screw (L). If the saw chain runs continuously or the engine
stops, adjust the idle speed, @ 23.2.
NOTICE
Engine power may drop noticeably if the saw is
subsequently used at temperatures above 14 °F (- 10 °C)
again. Reset the carburetor to the standard setting.
17.5 Standard Carburetor Setting
The carburetor comes from the factory with a standard
setting. This setting provides an optimum fuel-air mixture
under most operating conditions.
To return the carburetor to the standard setting:
► Shut off the engine and engage the chain brake.
► Turn the high speed screw (H) counter-clockwise as far as
stop.
► Turn the low speed screw (L) clockwise as far as stop,
then turn it back a 1/4 turn counter-clockwise.
18.1 Preparing for Transportation or Storage
WARNING
To reduce the risk of personal injury from unintended
activation or unauthorized use, shut off the engine and
engage the chain brake before transporting the chain saw or
putting it down. To reduce the risk of injuries from the sharp
cutters on the chain, always cover the guide bar with the
chain scabbard before transporting or storing the saw.
To prepare the saw for transportation or storage:
► Shut off the engine, @ 15.
► Release the chain brake and loosen the chain, @ 12.2.
► Re-engage the chain brake.
► Slide a chain scabbard over the guide bar so that it covers
the entire guide bar.
► Before using the saw, remember to re-tension the chain.
0000-GXX-3131-A0
L
18 After Finishing Work
0000-GXX-2946-A0
H
L