Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Product
- 5 IMPORTANT SAFETY INSTRUCTIONS
- 6 Kickback and Other Reactive Forces
- 7 Proper Techniques for Basic Bucking, Limbing, Pruning and Felling
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Assembling the Chain Saw
- 11 Lubricating the Saw Chain and Guide Bar
- 12 The Chain Brake
- 13 Mixing Fuel and Refueling the Chain Saw
- 14 Starting the Engine
- 15 Shutting Off the Engine
- 16 Checking the Chain Saw
- 17 Adjusting the Carburetor
- 18 After Finishing Work
- 19 Transporting
- 20 Storing
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Combinations of Guide Bars and Saw Chains
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Emission Control Warranty
- 30 Trademarks
- 31 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en el producto
- 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 6 Contragolpe y otras fuerzas reactivas
- 7 Técnicas adecuadas para el tronzado, el desramado, la poda y la tala básicos
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Armado de la motosierra
- 11 Lubricación de la cadena de aserrado y de la espada
- 12 El freno de cadena
- 13 Mezcla del combustible y carga de combustible en la motosierra
- 14 Arranque del motor
- 15 Apagado del motor
- 16 Revisión de la motosierra
- 17 Ajuste del carburador
- 18 Después de completar el trabajo
- 19 Transporte
- 20 Almacenamiento
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de espadas y cadenas de aserrado
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Garantía del sistema de control de emisiones
- 30 Marcas comerciales
- 31 Direcciones
0458-573-8621-D
45
English
15 Shutting Off the Engine
► Press down the throttle trigger lockout (1) and blip the
throttle trigger (2). The Master Control Lever (3) will move
to the run position and the engine will settle down to
idling speed.
► If the engine does not start after a few attempts, follow the
pre-starting procedure (@ 14.3) and try starting the
engine again.
► Disengage the chain brake, @ 12.2.
Your chain saw is ready for operation.
► If the saw chain rotates when the engine is idling, adjust
the idle speed, @ 23.2.
NOTICE
Accelerating the engine while the chain brake is engaged or
the chain is otherwise blocked (i.e., not able to turn)
increases the load and will cause the clutch to slip
continuously. This may occur if the throttle is depressed for
more than a few seconds when the chain is pinched in the
cut or the chain brake is engaged. To reduce the risk of
overheating and damage to important components (e. g.
clutch, polymer housing components), always disengage the
chain brake before accelerating engine and before starting
cutting work. The only exception to this rule is when you
check operation of the chain brake, @ 16.1.
15.1 Shutting Off the Engine
WARNING
The saw chain will continue to rotate for a short while after
the throttle trigger is released. To avoid serious or fatal
injury, avoid contact with the moving chain. To reduce the
risk of personal injury from unintended activation or
unauthorized use, shut off the engine, ensure the chain has
stopped and engage the chain brake before walking with the
saw or setting it down.
To shut off the engine:
► Release the throttle trigger (2) and throttle trigger
lockout (1).
► Move the Master Control Lever (3) to position 0.
16.1 Checking the Operation of the Chain Brake
WARNING
Operating the saw with a missing, damaged, modified or
improperly maintained chain brake increases the risk of
severe or fatal injury from kickback. Never attempt to modify
2
3
1
0000-GXX-6337-A0
15 Shutting Off the Engine
16 Checking the Chain Saw
2
3
1
0000-GXX-6355-A0