Instruction Manual
Table Of Contents
- STIHL MS 151 TC
- 1 Guide to Using this Manual
- 2 Safety Precautions
- 3 Reactive Forces
- 4 Working Techniques
- 5 Cutting Attachment
- 6 Mounting the Bar and Chain
- 7 Tensioning the Saw Chain (side chain tensioner)
- 8 Checking Chain Tension
- 9 Fuel
- 10 Fueling
- 11 Chain Lubricant
- 12 Filling Chain Oil Tank
- 13 Checking Chain Lubrication
- 14 Chain Brake
- 15 Starting / Stopping the Engine
- 15.1 Positions of the Master Control lever
- 15.2 Positions of Choke Shutter
- 15.3 Adjust Master Control lever
- 15.4 Manual fuel pump
- 15.5 Holding the Chain Saw
- 15.6 Actuating
- 15.7 Starting the Chainsaw
- 15.8 When Engine Begins to Fire
- 15.9 As Soon As the Engine Runs
- 15.10 At Very Low Outside Temperatures
- 15.11 Shut off the engine
- 15.12 If Engine Does Not Start
- 15.13 If Fuel Tank Has Been Run Completely Dry and Then Refueled
- 16 Operating Instructions
- 17 Taking Care of the Guide Bar
- 18 Cleaning the Air Filter
- 19 Adjusting the Carburetor
- 20 Spark Plug
- 21 Storing the Machine
- 22 Checking the Chain Sprocket
- 23 Maintaining and Sharpening the Saw Chain
- 24 Maintenance and Care
- 25 Main Parts
- 26 Specifications
- 27 Special Accessories
- 28 Ordering Spare Parts
- 29 Maintenance and Repairs
- 30 Disposal
- 31 EC Declaration of Conformity
WARNING
Depth gauges that are too low increase the kick‐
back tendency of the chain saw.
689BA052 KN
► Lay the file gauge on the saw chain – the high‐
est point of the depth gauge must be flush with
the file gauge
► After sharpening, clean the saw chain thor‐
oughly, removing any filings or grinding dust –
lubricate the saw chain thoroughly
► In the event of extended periods of disuse,
store saw chains in cleaned and oiled condi‐
tion
Sharpening tools (special accessories)
Chain pitch Round file
^
Round file File holder File gauge Taper square
file
Sharpening
set
1)
Inches (mm) mm (Inches
)
Part number Part number Part number Part number Part number
1/4P (6.35) 3.2 (1/8) 5605 771
3206
5605 750
4300
0000 893
4005
0814 252
3356
5605 007
1000
1/4 (6.35) 4.0 (5/32) 5605 772 40065605 750 43271110 893 40000814 252 33565605 007
1027
3/8 P (9.32) 4.0 (5/32) 5605 772
4006
5605 750
4327
1110 893
4000
0814 252
3356
5605 007
1027
0.325 (8.25) 4.8 (3/16) 5605 772
4806
5605 750
4328
1110 893
4000
0814 252
3356
5605 007
1028
3/8 (9.32) 5.2 (13/64) 5605 772
5206
5605 750
4329
1110 893
4000
0814 252
3356
5605 007
1029
0.404 (10.26) 5.5 (7/32) 5605 772
5506
5605 750
4330
1106 893
4000
0814 252
3356
5605 007
1030
1)consisting of file holder with round file, taper square file and file gauge
23 Maintaining and Sharpening the Saw Chain English
0458-508-8321-B 27