Instruction Manual
Table Of Contents
- STIHL MS 151 TC
- 1 Guide to Using this Manual
- 2 Safety Precautions
- 3 Reactive Forces
- 4 Working Techniques
- 5 Cutting Attachment
- 6 Mounting the Bar and Chain
- 7 Tensioning the Saw Chain (side chain tensioner)
- 8 Checking Chain Tension
- 9 Fuel
- 10 Fueling
- 11 Chain Lubricant
- 12 Filling Chain Oil Tank
- 13 Checking Chain Lubrication
- 14 Chain Brake
- 15 Starting / Stopping the Engine
- 15.1 Positions of the Master Control lever
- 15.2 Positions of Choke Shutter
- 15.3 Adjust Master Control lever
- 15.4 Manual fuel pump
- 15.5 Holding the Chain Saw
- 15.6 Actuating
- 15.7 Starting the Chainsaw
- 15.8 When Engine Begins to Fire
- 15.9 As Soon As the Engine Runs
- 15.10 At Very Low Outside Temperatures
- 15.11 Shut off the engine
- 15.12 If Engine Does Not Start
- 15.13 If Fuel Tank Has Been Run Completely Dry and Then Refueled
- 16 Operating Instructions
- 17 Taking Care of the Guide Bar
- 18 Cleaning the Air Filter
- 19 Adjusting the Carburetor
- 20 Spark Plug
- 21 Storing the Machine
- 22 Checking the Chain Sprocket
- 23 Maintaining and Sharpening the Saw Chain
- 24 Maintenance and Care
- 25 Minimize Wear and Avoid Damage
- 26 Main Parts
- 27 Specifications
- 28 Special Accessories
- 29 Ordering Spare Parts
- 30 Maintenance and Repairs
- 31 Disposal
- 32 EC Declaration of Conformity
19.4 Adjusting Idle Speed
► Carry out the standard setting.
► Start the engine.
Warm up the engine. Allow engine to idle for
10 seconds before adjusting the idle speed.
3006BA025 KN
Engine stops while idling
► Turn the idle speed screw (LA) clockwise until
the chain begins to run – then back it off
4 turns.
Saw chain runs while engine is idling
► Turn the idle speed screw (LA) counterclock‐
wise until the chain stops moving – allow
engine to run at idle speed for 10 seconds.
► Turn the idle speed screw (LA) clockwise until
the chain begins to run – then back it off
4 turns.
WARNING
If the chain continues moving when the engine is
idling, have your saw checked and repaired by
your servicing dealer.
Erratic idling behavior, poor acceleration (even
though standard setting of low speed screw is
correct)
Idle setting is too lean
► Turn the low speed screw (L) carefully coun‐
terclockwise, no further than stop, until the
engine runs smoothly and accelerates well.
It is usually necessary to change the setting of
the idle speed screw (LA) after every correction
to the low speed screw (L).
19.5 Fine Tuning for Operation at
High Altitude
A slight correction of the setting may be neces‐
sary if the engine does not run satisfactorily:
► Carry out the standard setting.
► Warm up the engine.
► Turn high speed screw (H) slightly clockwise
(leaner) – no further than stop.
NOTICE
After returning from high altitude, reset the car‐
buretor to the standard setting.
If the setting is too lean there is a risk of engine
damage due to insufficient lubrication and over‐
heating.
20 Spark Plug
► If the engine is down on power, difficult to start
or runs poorly at idle speed, first check the
spark plug.
► Fit a new spark plug after about 100 operating
hours – or sooner if the electrodes are badly
eroded. Install only suppressed spark plugs of
the type approved by STIHL – see "Specifica‐
tions".
20.1 Removing the Spark Plug
► Move the Master Control lever to 0 or STOP.
3006BA001 KN
► Disengage the chain brake.
1
2011BA002 KN
2
► Unscrew the nut (1) and remove the sprocket
cover (2).
English 20 Spark Plug
22 0458-508-0121-B