Instruction Manual

ManualsBrandsSTIHL ManualsCordless power systemsTelescopic pole pruner: With 30 cm / 12" bar and 3/8" P saw chain

Table Of Contents

1 Introduction
2 Guide to Using this Manual
- 2.1 Applicable Documents
- 2.2 Symbols used with warnings in the text
- 2.3 Symbols in Text
3 Overview
- 3.1 STIHL HTA 135 Pole Pruner and Battery
- 3.2 Icons
4 Safety Precautions
- 4.1 Warning Symbols
- 4.2 Intended Use
- 4.3 The Operator
- 4.4 Clothing and equipment
- 4.5 Work Area and Surroundings
  - 4.5.1 Pole Pruner
  - 4.5.2 Battery
- 4.6 Safe Condition
- 4.7 Working
  - 4.7.1 Sawing
  - 4.7.2 Limbing
- 4.8 Reactive Forces
- 4.9 Transporting
  - 4.9.1 Pole Pruner
  - 4.9.2 Battery
- 4.10 Storing
  - 4.10.1 Pole Pruner
  - 4.10.2 Battery
- 4.11 Cleaning, Maintenance and Repair
5 Preparing Pole Pruner for Operation
- 5.1 Preparing the Pole Pruner for Operation
6 Charging the Battery, LEDs
- 6.1 Charging the Battery
- 6.2 Displaying State of Charge
- 6.3 LEDs on Battery
7 Assembling the Pole Pruner
- 7.1 Assembling the Pole Pruner
- 7.2 Attaching the clip
- 7.3 Mounting the machine support
- 7.4 Mounting and Removing the Bar and Chain
  - 7.4.1 Mounting the Guide Bar and Saw Chain
  - 7.4.2 Removing the Guide Bar and Saw Chain
- 7.5 Tensioning the Saw Chain
- 7.6 Filling Up with Saw Chain Oil
8 Removing and Fitting the Battery
- 8.1 Inserting the Battery
- 8.2 Removing the Battery
9 Switching Pole Pruning On and Off
- 9.1 Switching on the Pole Pruner
- 9.2 Switching the Pole Pruner Off
10 Checking Pole Pruner and Battery
- 10.1 Checking the Chain Sprocket
- 10.2 Checking the Guide Bar
- 10.3 Checking the Saw Chain
- 10.4 Checking the controls
- 10.5 Checking Chain Lubrication
- 10.6 Testing the Battery
11 Using the Pole Pruner
- 11.1 Adjusting the shaft length
- 11.2 Aligning the clip
- 11.3 Fitting and Adjusting the Shoulder Strap
- 11.4 Holding and Controlling the Pole Pruner
- 11.5 Limbing
12 After Finishing Work
- 12.1 When Work is Finished
13 Transporting
- 13.1 Transporting the Pole Pruner
- 13.2 Transporting the battery
14 Storing
- 14.1 Storing the Pole Pruner
- 14.2 Storing the Battery
15 Cleaning
- 15.1 Cleaning the Pole Pruner
- 15.2 Cleaning the Guide Bar and Saw Chain
- 15.3 Cleaning the Air Filter
- 15.4 Cleaning the Battery
16 Maintenance
- 16.1 Maintenance intervals
- 16.2 Deburring the Guide Bar
- 16.3 Sharpening the Saw Chain
17 Repairing
- 17.1 Repairing the Pole Pruner and Battery
18 Troubleshooting
- 18.1 Troubleshooting Pole Pruner and Battery
19 Specifications
- 19.1 STIHL HTA 135 pole pruner
- 19.2 Chain Sprockets
- 19.3 Minimum Groove Depth of Guide Bars
- 19.4 STIHL AP battery
- 19.5 Sound Values and Vibration Values
- 19.6 REACH
20 Bar and Chain Combinations
- 20.1 STIHL HTA 135 pole pruner
21 Combinations of Carrying Systems
- 21.1 Combinations of Carrying Systems
22 Spare Parts and Accessories
- 22.1 Spare parts and accessories
23 Disposal
- 23.1 Disposing of Pole Pruner and Battery
24 EC Declaration of Conformity
- 24.1 STIHL HTA 135 pole pruner
25 General Power Tool Safety Warnings
- 25.1 Introduction
- 25.2 Work area safety
- 25.3 Electrical safety
- 25.4 Personal safety
- 25.5 Electric power tool use and care
- 25.6 Battery tool use and care
- 25.7 Service

0458-698-0121-A

English

18 Troubleshooting

The battery service life has

been exceeded.

► Replace battery.

Smell of smoke or

burning in the cutting

area.

The saw chain has not

been correctly sharpened.

Sharpen chain as specified.

Insufficient saw chain oil in

the oil tank.

Fill up with saw chain oil.

The chain lubrication

system is supplying

insufficient saw chain oil.

Do not use your pole pruner and contact your STIHL

servicing dealer for assistance.

The saw chain is over-

tensioned.

Tension the saw chain as specified.

The pole pruner is not

being used correctly.

Have correct use explained, then practice.

Fault LEDs on the

battery

Cause Remedy