Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Battery Safety
- 8 Maintenance, Repair and Storage
- 9 Before Starting Work
- 10 Charging the Battery
- 11 LED Diagnostics and Acoustic Signals
- 12 STIHL AR Backpack Battery
- 13 Assembling the Hedge Trimmer
- 14 Inserting and Removing the Battery
- 15 Switching the Hedge Trimmer On and Off
- 16 Checking the Controls
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting the Hedge Trimmer and Battery
- 20 Storing the Hedge Trimmer and Battery
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Approved Harness Combinations
- 26 Replacement Parts and Equipment
- 27 Disposal
- 28 Limited Warranty
- 29 Trademarks
- 30 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 5.1 Introducción
- 5.2 Seguridad en la zona de trabajo
- 5.3 Seguridad eléctrica
- 5.4 Seguridad personal
- 5.5 Uso y cuidado de la herramienta motorizada
- 5.6 Uso y cuidado de la herramienta con batería
- 5.7 Mantenimiento
- 5.8 Advertencias de seguridad del cortasetos
- 5.9 Advertencias de seguridad del cortasetos de alcance extendido
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Seguridad de la batería
- 8 Mantenimiento, reparación y almacenamiento
- 9 Antes de empezar a trabajar
- 10 Carga de la batería
- 11 Diagnóstico por LED y señales acústicas
- 12 Batería de mochila STIHL AR
- 13 Armado del cortasetos
- 14 Colocación y extracción de la batería.
- 15 Encendido y apagado del cortasetos
- 16 Revisión de los controles
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte del cortasetos y de la batería
- 20 Almacenamiento del cortasetos y de la batería
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Combinaciones de arnés aprobadas
- 26 Piezas y equipos de repuesto
- 27 Eliminación
- 28 Garantía limitada
- 29 Marcas comerciales
- 30 Direcciones
0458-185-8621-A
22
English
11 LED Diagnostics and Acoustic Signals
► Push the battery (2) into the charger (3) until it stops.
The LED on the charger glows green when the battery is
charging.
The LEDs (1) on the AP battery glow green and show the
state of charge.
When the LEDs on the battery go out, the charging
process is complete and the charger will shut itself off. The
AP battery can be removed from the charger.
► Disconnect the power supply cord from the electrical
outlet when the charger is not in use.
► Charge STIHL AP series batteries only with genuine
STIHL AL 101, AL 300 or AL 500 series chargers.
11.1 STIHL AP Battery
11.1.1 Battery Status
Four LEDs show the status of the battery. These LEDs can
glow or flash green or red.
11.1.2 Power Tool Status
The same LEDs on the battery will indicate the status of the
power tool.
If three LEDs glow red continuously: the power tool motor is
too hot. Allow the motor to cool down.
If three LEDs flash red when you activate the trigger switch:
the power tool has an electrical malfunction. Do not operate
the power tool. Have it checked by an authorized STIHL
servicing dealer before use or storage.
For troubleshooting information, @ 23.
11.1.3 Charge Status
The LEDs on the battery also show the battery's state of
charge.
To determine the battery's state of charge:
► Press the button (1) on the battery.
The LEDs on the battery will glow or flash green for about
5 seconds and indicate the state of charge (see
illustration).
For example:
If four green LEDs glow continuously: full charge.
If one green LED is flashing: less than 20 % charge.
11.2 STIHL AR Backpack Battery
11.2.1 Battery Status
Six LEDs and an acoustic signal indicate the status of the
battery.
11 LED Diagnostics and Acoustic Signals
If one LED glows red continuously: the battery is
either too hot or too cold. Allow the battery to
warm up or cool down gradually at an ambient
temperature of about 50 °F to 68 °F (10 °C to
20 °C).
If all 4 LEDs flash red: the battery has a
malfunction and must be replaced. Do not
attempt to charge, use or store the battery.
1
0000-GXX-1248-A0
20-40%
40-60%
60-80%
80-100%
0-20%