Instruction Manual
Table Of Contents
- 1 Introduction
- 2 Guide to Using this Manual
- 3 Main Parts
- 4 Safety Symbols on the Products
- 5 General Power Tool Safety Warnings
- 6 IMPORTANT SAFETY INSTRUCTIONS
- 7 Battery Safety
- 8 Charger Safety
- 9 Maintenance, Repair and Storage
- 10 Before Starting Work
- 11 Charging the Battery
- 12 LED Diagnostics
- 13 Assembling the Hedge Trimmer
- 14 Inserting and Removing the Battery
- 15 Switching the Hedge Trimmer On and Off
- 16 Checking the Controls
- 17 During Operation
- 18 After Finishing Work
- 19 Transporting the Hedge Trimmer and Battery
- 20 Storing the Hedge Trimmer, Battery and Charger
- 21 Cleaning
- 22 Inspection and Maintenance
- 23 Troubleshooting Guide
- 24 Specifications
- 25 Replacement Parts and Equipment
- 26 Disposal
- 27 Limited Warranty
- 28 Trademarks
- 29 Addresses
- 1 Introducción
- 2 Acerca de este manual de instrucciones
- 3 Componentes importantes
- 4 Símbolos de seguridad en los productos
- 5 Advertencias generales de seguridad para herramientas motorizadas
- 6 INSTRUCCIONES IMPORTANTES DE SEGURIDAD
- 7 Seguridad de la batería
- 8 Seguridad del cargador
- 9 Mantenimiento, reparación y almacenamiento
- 10 Antes de empezar a trabajar
- 11 Carga de la batería
- 12 Diagnóstico de LED
- 13 Armado del cortasetos
- 14 Colocación y extracción de la batería.
- 15 Encendido y apagado del cortasetos
- 16 Revisión de los controles
- 17 Durante el funcionamiento
- 18 Después de completar el trabajo
- 19 Transporte del cortasetos y de la batería
- 20 Almacenamiento del cortasetos, la batería y el cargador
- 21 Limpieza
- 22 Inspección y mantenimiento
- 23 Guía de solución de problemas
- 24 Especificaciones
- 25 Piezas y equipos de repuesto
- 26 Eliminación
- 27 Garantía limitada
- 28 Marcas comerciales
- 29 Direcciones
0458-816-8621-A
20
English
10 Before Starting Work
10.1 Preparing the Hedge Trimmer for Operation
Before starting work:
► Fully charge the battery, @ 11.
► Mount the hedge trimmer's loop handle, @ 13.2.
► Mount the cutting blades, @ 13.1.
► Check the controls for proper function and condition,
@ 16.1.
► Check the cutting attachment for damage or other
problems.
11.1 Setting up the Charger
WARNING
Read and follow the battery and charger safety precautions
and instructions in this manual, @ 7 and @ 8. To reduce
the risk of short circuit, which could lead to electric shock,
fire and explosion, make sure the charger and its
components are dry and not damaged; operate the charger
indoors at an appropriate ambient temperature, @ 8.
WARNING
Since the battery and charger heat up during the charging
process, do not operate the charger on a combustible
surface or in a location where combustible gases, liquids,
vapors, dusts or other materials and substances are
present, @ 8.
To set up the charger:
► Insert the plug (3) into a properly installed wall outlet (4)
matching the voltage and electrical frequency stated on
the rating plate on the charger.
The charger runs a self-test immediately after it is plugged
in. The charger LED (1) will glow green for about 1 second,
then it will glow red briefly before going out. Once the LED
goes out, the self-test is complete and the charger is ready
to charge the battery.
► Position the power supply cord (2) so that it will not be
stepped on, tripped over, come in contact with sharp
objects or moving parts or otherwise present a tripping
hazard or be subjected to damage or stress.
11.2 Charging
WARNING
STIHL batteries contain safety features and devices which,
if damaged, may allow the battery to generate heat, rupture,
leak, ignite or explode. Never charge a malfunctioning,
damaged, cracked, leaking or deformed battery or use a
charger that has been damaged. For indoor use only. Keep
the charger dry. Protect it from rain, water, liquids and damp
conditions. Never insert a wet battery. Never use a wet
charger, @ 8.
10 Before Starting Work
11 Charging the Battery
3
2
1
2
0000-GXX-0636-A1
4