Product Warranty

ManualsBrandsStiga ManualsFamily RecreationExpert Roller Table Tennis Table

2L-6670-00

OWNER'S

MANUAL

MODEL NOS.

T8220-1

READ THESE

INSTRUCTIONS

CAREFULLY!

CAUTION

Tools Needed: ! Two 7/16 Open \ Boxed End Wrenches ! Two ½ Wrenches

! Tape Measure ! Two 9/16 Open \ Boxed End Wrenches

EXPERT ROLLER

Thank you for buying our product. We try hard to ensure that our products are of high quality and

free of problems, such as manufacturing defects or missing parts. However, if you have any

problems with your new product, please DO NOT RETURN IT TO THE STORE!.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Call us at:

TOLL FREE 1-866-873-3528

(THIS IS A CONSUMER ONLY NUMBER)

Please have this Owner’s Manual with you when you call.

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706

Fax Number: (812) 467-1399.

Or E-mail us at: customerservice@escaladesports.com

Please provide model number and/or part number (not just the key number) of the product and/or part

when you call or write. These numbers can be found on the product, packaging, and/or in this Owner’s

Manual.

Summary of content (8 pages)

PAGE 1
OWNER'S MANUAL EXPERT ROLLER MODEL NOS. T8220-1 Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as manufacturing defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT TO THE STORE!. DO NOT RETURN THIS PRODUCT TO THE STORE! Call us at: TOLL FREE 1-866-873-3528 (THIS IS A CONSUMER ONLY NUMBER) Please have this Owner’s Manual with you when you call.
PAGE 2
1. ATTACHING LEGS TO TABLE TOPS CAUTION AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE FOLLOWING STEPS! 1. Leave top halves #1 in shipping carton as shown 3. Put caps #21 on bottom end of leg assembly above or lay them on a carpeted floor (to protect #10. (See Detail C). them from damage and scratches ). 4. Attach upright assembly #11 to remaining 2. Attach leg assembly #10 to brackets #6 located brackets #6 on the bottom of the first top half #1. on the bottom of the first top half #1. (See above).
PAGE 3
2. ATTACHING NAME PANELS TO LEGS CAUTION AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE FOLLOWING STEPS! DO NOT LEAVE TABLE UNATTENDED UNTIL ASSEMBLY IS COMPLETE! 6. With a helper helper,, hold top halves about 15 ½ inches apart. Attach only one half of name panels #8 to upright assemblies #11 as shown above. Use ONLY TWO bolts #25 and locknuts #29 on each name panel.
PAGE 4
3. ATTACHING LINKAGE TO LEGS 8. Attach linkages #24 to upright assembly #11 using bolts #27, spacers #18, and locknuts #29. (See Detail F). The lip on step spacers #18 fit into the larger hole in linkages #24. NOTE: If you have trouble inserting bolts #27 through name panels #8, slightly loosen bolts #25 (that you used in the previous section to attach name panels #8). (See Section 2 on previous page). 9. Attach other end of linkages #24 to leg assembly #10 using bolts #26, spacers #20, and locknuts #28.
PAGE 5
4. ATTACHING CASTERS 11. Put caps #15 into ends of caster beams #12 (see Detail H). 12. Attach one non-locking caster #13 and one locking caster #14 to each caster beam #12 with locknuts #17. (See Detail H). TIGHTEN CASTERS BUT DO NOT OVERTIGHTEN CRUSHING TUBES. 13. Attach caster beams to upright assemblies #11 with bolts #25, washers #23, and spacer bushings #19. NOTE: Spacers bushings #19 slide INSIDE caster beams #12 to keep beams from crushing. (See Detail J). Tighten bolts #25 tight. 14.
PAGE 6
5. SETTING TABLE UPRIGHT CAUTION At least two adults are needed to complete the following steps. Be sure top halves are locked in safety latches! Be sure that both locking casters are locked! You must use a 7" stack of magazines (or similar block) to protect the casters when lifting table upright! 15. Before lifting table, be sure both top halves are locked in safety latches! Be sure casters are locked! Put a 7 inch stack of magazines, wood, etc. under caster beam nearest the floor to protect casters.
PAGE 7
FINISHING THE ASSEMBLY NOTE: If sides of table are not even with one another, loosen the bottom four bolts that were loosened in step #18 and push both sides inward as shown until they are even. Retighten bolts when sides are even.
PAGE 8
CAUTION This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme temperature changes which occur on patios, or similar areas, can cause wood to warp, swell, crack or blister. UNLEVEL FLOORS: If your table does not seem level, it is probably because the floor is not level. Move table around several inches to find the best location for the table (first be sure table is in playing position). If floor is extremely unlevel, the table may not play or operate properly.