ST IG A T U RBO 55 COMBI 48 COMBI 43 COMBI 8211-0208-11
S SVENSKA B 1. 2. B 3. 4. D F E 5. 6. 7.
S SVENSKA FULL ADD FULL ADD 9. Briggs & Stratton LS 45 FULL 8. ADD 0,15 l. FULL/MAX ADD/MIN 10. Briggs & Stratton XTE 11. Honda GCV 3x 12. Briggs & Stratton LS 45 13. Briggs & Stratton XTE G I* B* 14. Honda GCV 15.
S SVENSKA X 16. Y 17. 18. 19. Left 21. Briggs & Stratton LS 45 22. Briggs & Stratton XTE 23. Honda GCV 24. 20.
S SVENSKA 25. 26. S S T 27. 28. 40 Nm 40 Nm 29. Regular blade holder 30. Friction blade holder S 31 A. 48 cm / 55 cm 31 B.
GB ENGLISH SYMBOLS 3 The following symbols can be found on the machine to remind you of the care and attention that are required during use. 5 2 The symbols mean: Warning! Read the Instruction Book and Safety Manual before using the machine. 4 Warning! Keep hands and feet clear of the cutting deck when the machine is running. Type II 3 2 STOP Warning! Keep onlookers away. Beware of objects being flung out.
GB ENGLISH INSTALLATION LOOSE PARTS IN THE BOX 2 brackets for the grass collector 4 screws for the brackets 1 ignition key (*) 1 battery charger (*) 1 Allen key 1 socket wrench + Instruction books HANDLE (Type I-III) 1. Fold up the lower part of the handle. 2. Install the upper part of the handle mounts using screws, washers and locking wheels. A lug is installed on the right hand side for the starter handle (fig. 1). 3. Then tighten the locking wheels onto the lower part of the handle.
GB ENGLISH To remove the plug, press in the catch (S). On reinstalling the plug ensure that both pins are pressed firmly into the holes so that the plug snaps in place. Turbo 43 Combi: To remove the plug, unscrew the wing nut. 2. COLLECTION Assemble the grass collector provided (fig. 6, 8). Open the flap, remove the plug and instead hook the collector onto the rear of the machine. When mowing, the grass is collected in the collector.
GB ENGLISH STARTING THE ENGINE (Honda) REAR WHEEL DRIVE (*) 1. Place the lawnmower on flat, firm ground. Do not start in long grass. Engage the drive by pressing the clutch loop I towards the handle. Disengage the drive by releasing the clutch loop I (fig. 15). 2. Make sure the spark plug cable is connected to the spark plug. 3. Open the fuel tap (fig. 14). 4. Set the throttle control B in the choke position . NOTE! It is not necessary to use the choke position when the engine is warm (fig. 15). 5.
GB ENGLISH If grass has dried on to the mower casing, it can be scraped clean. If necessary, touch up the underside with paint to prevent rust damage. Clean the silencer and the surrounding area regularly to remove grass, dirt and flammable waste products. Remove the transmission casing by removing the screws S (fig. 27) and clean around the transmission (*) and drive belts (*) with a brush or compressed air once or twice a year. Once every season, the drive wheels (*) should be cleaned internally.
GB ENGLISH BATTERY (*) The electrolyte in the battery is toxic and corrosive. It can cause serious corrosion damage etc. Avoid all contact with skin, eyes and clothing. In normal use during the season, the battery is charged by the engine. If the engine cannot be started with the ignition key, it may be because the battery is 'dead'. 2. When the clutch loop is pressed in approx. 2 cm (position 1), there should be some resistance when pushing the lawnmower.
ENGLISH GB When replacing the blade, the blade screw should also be replaced. The guarantee does not cover damage to the blade, blade holder or engine caused by running into obstacles. When replacing the blade, blade holder and blade screw, always use genuine spare parts. Non-genuine spare parts can entail a risk of injury or damage, even if they fit the machine. SHARPENING THE BLADES Sharpening of the blades must be done by wet method grinding, using a whetstone or a grindstone.
M OW I N G A H E A D BOX 1006 · SE-573 28 TRANÅS w w w. s t i g a .
