Submittal Sheet

17 West St., W. Hatfield, MA 01088 | 800.582.8423 | 413.247.3380 | fax [phone] | info
@
stiebel-eltron-usa.com | www.stiebel-eltron-usa.com
rev. 2014.1 | Due to our continuous process of engineering and technological advancement, specifications may change without notice.
rev. 2014.1 | Due to our continuous process of engineering and technological advancement, specifications may change without notice.
LIMITED WARRANTY
STIEBEL ELTRON, Inc. warrants to the original owner that the GALAXY
TM
hand dryer will be free from
defects in workmanship and materials for a period of FIVE YEARS from the date of purchase. Should
any part(s) prove to be defective under normal use during this period, STIEBEL ELTRON, Inc. will be
responsible for replacement of the defective part(s) only. Damage to the housing due to abuse is not
covered by this warranty. STIEBEL ELTRON, Inc. is not responsible for labor charges to remove and/or
replace the defective part(s), or any incidental or consequential expenses. Should the owner wish to
return the entire unit for repair, the owner must first secure written authorization from STIEBEL ELTRON, Inc.
The owner shall be required to show proof of purchase date by including a copy of the original
invoice, and to pay all transportation costs to return defective part(s) or hand dryer for repair or
replacement.
IF YOU NEED TO RETURN A PART OR A HAND DRYER UNDER WARRANTY, PLEASE CALL US FIRST TO
OBTAIN SHIPPING INSTRUCTIONS. REMEMBER TO SEND A COPY OF THE INVOICE WITH YOUR RETURNED
PART.
STIEBEL ELTRON, Inc.
17 West Street
West Hatfield, MA 01088
Phone: [phone]
Operating Instructions
for the user
In order to dry your hands most efficiently, please use the
following procedure:
• shake off excess water over the wash basin
• place hands underneath the unit at a distance of 4" - 7"
• rub your hands together as if you were washing them
Your hands will be dry within 25 - 35 seconds.
The STIEBEL ELTRON GALAXY
TM
series hand dryers are equipped
with an infrared sensor switch. This sensor will activate the unit
when hands are placed underneath it. Approximately 7
seconds after the hands have been removed, the unit will
automatically shut off.
The sensor is the black rectangle located underneath the unit
between the air exit and air inlet grills. The sensor switch will not
work properly if it has been covered by gum or dirt. If the sensor
is obstructed, the hand dryer will switch off automatically to
prevent it from running continuously. Should the unit overheat,
a safety high-limit switch will turn off the heating element. The
safety high-limit switch resets automatically once the heating
element has had a chance to cool down.
Normal Care
T
o clean the case use a soft cloth with a mild detergent if
necessary. Never use any abrasive cleaners since they will
scratch the finish of the unit. Never spray water or cleaning
fluids directly on hand dryer. While cleaning the unit, make sure
the electric eye switch is not covered. THE GALAXY
TM
HAND
DRYER DOES NOT CONTAIN ANY PARTS SERVICEABLE BY THE LAY
PERSON. IN CASE OF MALFUNTION PLEASE CONTACT A LICENSED
ELECTRICIAN.
48"
120 cm
min. 4"
10 cm
FIG. 1
Dimensions & Colors
Specication
Engineer/Architect ________________________________________________________________________________________________________________________________________________________________________________________________ Date _________________________________________________________________________________________________________________________________________________________
Job Name/Customer ____________________________________________________________________________________________________________________________________________________________________________________________ Location _____________________________________________________________________________________________________________________________________________
Contractor _______________________________________________________________________________________________________________________________________________________________________________________________________________________ Representative ___________________________________________________________________________________________________________________________
Qty kW Voltage Amps
Galaxy
™
model _______________________________________________________________ _____________________________ ____________________________ ____________________________ ____________________________
Galaxy
™
1 & 2 hand dryers shall be manufactured by Stiebel Eltron, Inc. to include a cover of ABS polycarbonate designed for light to
medium traffic areas. Motor shall be thermally protected brush type with a single shaft. Dryer shall deliver 90 cubic feet per minute
of air volume and shall be activated by an infrared sensor automatically detecting hands when present. Hand dryer shall be listed under
of ETL as conforming to ANSI/UL Std. 499 and certified to CAN/CSA Std. 22.2 No. 36.
Galaxy
™
M1 & M2 hand dryers shall be manufactured by Stiebel Eltron, Inc. to include a cover of cast aluminum designed for high traffic
areas. Motor shall be thermally protected brush type with a single shaft. Dryer shall deliver 95 cubic feet per minute of air volume
and shall be activated by an infrared sensor automatically detecting hands when present. Hand dryer shall be listed under of ETL as
conforming to ANSI/UL Std. 499 and certified to CAN/CSA Std. 22.2 No. 36.
GALAXY with Plastic Housing
Installation Instructions for the
Licensed Installer
DO NOT INSTALL UNIT WHERE IT CAN ACCIDENTALLY BE
SPLASHED WITH WATER, ELECTRIC SHOCK MAY RESULT.
WARNING: BEFORE BEGINNING ANY WORK ON THE ELECTRIC
INSTALLATION, BE SURE THE MAIN BREAKER PANEL SWITCH IS
“OFF” TO AVOID ANY DANGER OF ELECTRIC SHOCK.
NOTE: THE CIRCUIT SHOULD BE EQUIPPED WITH A “GROUND
FAULT INTERRUPTER” WHERE REQUIRED BY LOCAL, STATE OR
NATIONAL ELECTRICAL CODES.
1. All electrical work must comply with national and
applicable state and local electrical codes.
2. The GALAXY
TM
hand dryer must have its own
independent circuit using 3 wire cable of the appropriate
size protected by a correctly rated double pole circuit
breaker. The GALAXY
TM
1 unit for 110-120V requires a 20
amp circuit breaker and a gauge #12 copper wire. The
GALAXY
TM
2 unit for 220-240V or 208V requires a 15 amp
circuit breaker and a gauge #12 copper wire.
3. Install unit so that the bottom is approximately 48" above
floor. Unit should be at least 4" from a perpendicular wall.
(FIG. 1, previous page)
4. Transfer the four mounting points to the wall by using the
enclosed drilling template and drill mounting holes.
5. Remove the two screws at the air outlet grill and the
screw on the locking bolt (FIG. 2).
6. Pull down locking bolt. Remove front part of housing
(FIG. 2).
7. Install a 1/2" electrical connector in the back part of
housing in the hole located below the wiring block.
8. Feed wires through connector; tighten clamp down on
wire. Mount back part of housing to the wall.
9. The “live” wires must be connected to the slots on the
terminal marked N/L and L. Ground wire must be
connected to the wire terminal on the blower housing with
the ground symbol.
WARNING: AS WITH ANY ELECTRIC APPLIANCE, FAILURE TO
ELECTRICALLY GROUND UNIT MAY RESULT IN SERIOUS INJURY
OR DEATH.
10. Reinstall front cover, push up locking bolt and reinstall
the three screws that were removed earlier.
Technical Data
GALAXY
TM
1: 120V, 60 Hertz, 1850 Watts
(Heating element 1800 Watts, motor 50 W)
GALAXY
TM
2: At 240V, 60 Hertz, 2000 Watts
(Heating element 1950 Watts, motor 50 W)
At 208V, 60 Hertz, 1500 Watts
(Heating element 1450 Watts, motor 50 W)
For dimensions see figure 3. The weight of the unit without shipping
materials is 5.5 lbs (2.5 kg).
6 7/8"
175 mm
9 1/16" 230 mm
9 7/8"
250 mm
6 7/8" 175 mm
FIG. 2
FIG. 3
TM
1
2
3
1M
~
N/L L
GRD
N/L
L
1 Fan Motor
2 Heating Element
3 Sensor
GRD
208—240V/60Hz
110—120V/60Hz
GALAXY with Plastic Housing
Installation Instructions for the
Licensed Installer
DO NOT INSTALL UNIT WHERE IT CAN ACCIDENTALLY BE
SPLASHED WITH WATER, ELECTRIC SHOCK MAY RESULT.
WARNING: BEFORE BEGINNING ANY WORK ON THE ELECTRIC
INSTALLATION, BE SURE THE MAIN BREAKER PANEL SWITCH IS
“OFF” TO AVOID ANY DANGER OF ELECTRIC SHOCK.
NOTE: THE CIRCUIT SHOULD BE EQUIPPED WITH A “GROUND
FAULT INTERRUPTER” WHERE REQUIRED BY LOCAL, STATE OR
NATIONAL ELECTRICAL CODES.
1. All electrical work must comply with national and
applicable state and local electrical codes.
2. The GALAXY
TM
hand dryer must have its own
independent circuit using 3 wire cable of the appropriate
size protected by a correctly rated double pole circuit
breaker. The GALAXY
TM
1 unit for 110-120V requires a 20
amp circuit breaker and a gauge #12 copper wire. The
GALAXY
TM
2 unit for 220-240V or 208V requires a 15 amp
circuit breaker and a gauge #12 copper wire.
3. Install unit so that the bottom is approximately 48" above
floor. Unit should be at least 4" from a perpendicular wall.
(FIG. 1, previous page)
4. Transfer the four mounting points to the wall by using the
enclosed drilling template and drill mounting holes.
5. Remove the two screws at the air outlet grill and the
screw on the locking bolt (FIG. 2).
6. Pull down locking bolt. Remove front part of housing
(FIG. 2).
7. Install a 1/2" electrical connector in the back part of
housing in the hole located below the wiring block.
8. Feed wires through connector; tighten clamp down on
wire. Mount back part of housing to the wall.
9. The “live” wires must be connected to the slots on the
terminal marked N/L and L. Ground wire must be
connected to the wire terminal on the blower housing with
the ground symbol.
WARNING: AS WITH ANY ELECTRIC APPLIANCE, FAILURE TO
ELECTRICALLY GROUND UNIT MAY RESULT IN SERIOUS INJURY
OR DEATH.
10. Reinstall front cover, push up locking bolt and reinstall
the three screws that were removed earlier.
Technical Data
GALAXY
TM
1: 120V, 60 Hertz, 1850 Watts
(Heating element 1800 Watts, motor 50 W)
GALAXY
TM
2: At 240V, 60 Hertz, 2000 Watts
(Heating element 1950 Watts, motor 50 W)
At 208V, 60 Hertz, 1500 Watts
(Heating element 1450 Watts, motor 50 W)
For dimensions see figure 3. The weight of the unit without shipping
materials is 5.5 lbs (2.5 kg).
6 7/8"
175 mm
9 1/16" 230 mm
9 7/8"
250 mm
6 7/8" 175 mm
FIG. 2
FIG. 3
TM
1
2
3
1M
~
N/L L
GRD
N/L
L
1 Fan Motor
2 Heating Element
3 Sensor
GRD
208—240V/60Hz
110—120V/60Hz
Conforms to
ANSI/UL Std. 499
Certified to
CAN/CSA
Std. 22.2 No. 36
Galaxy
™
MGalaxy
™
Alpine White
Alpine White
Charcoal Gray Metallic
Silver Metallic