User's Manual

ManualsBrandsSTid ManualsElectronicsTag Reader

13.56 MHz

Upgradable readers ARC

Installation instructions

13,56 MHz

Lecteurs évolutifs ARC

Notice d’installation

13.56 MHz

Lectores escalables ARC

Procedimiento de instalación

conforme con NOM-024 -SCFI-2013

Product references

Power supply characteristics

Use an AC/DC power supply type LPS, Limited Power Source (as per IEC/UL/EN 60950-1 Ed2) or type ES1, PS1 (according to IEC/UL/EN 62368-1) for the main

supply.

Main power supply: Range: +7 Vdc to +28 Vdc Typical: 12 Vdc

Max. consumption at 12 Vdc:

ARC-A: 130 mA

ARC-B: 160 mA

ARC-C: 200 mA

ARC-D: 280 mA

ARC-E: 310 mA

ARC-F: 350 mA

ARC-I: 160 mA

ARC-J: 190 mA

ARC-K: 230 mA

ARC-AQ: 260 mA

ARC-BQ: 290 mA

ARC-CQ: 330 mA

Characteristics

Communication: RS485 (L+ & L-) / RS232 (TD & RD) / TTL (Wiegand / Clock and Data)

Connection: Removable connectors 1x10 pins and 1x2 pins, thread 0.19685 inch

Protection: IP65, excluding connectors

Static relay: ASSR-1218-003E: 60 V output withstand voltage / 0.2A current rating / low on-resistance 1 Ω typical for AC/DC

Recommended cables

RS485: Use a multi-conductor shielded twisted pair cable. Max. length: 3281 ft at 9600 baud

RS232: Max. length 49.2 ft

Wiegand / Clock & Data: Use an untwisted shielded multi-conductor. For data:

2 wires AWG24 – 98 ft max / 4 wires AWG24 – 197 ft max / 6 wires AWG24 – 328 ft max

2 wires AWG20 – 164 ft max / 4 wires AWG20 – 328 ft max

Buzzer / LED

The operating mode for the Buzzer and LED 1 and 2 can be programmed by a configuration card (R3x & S3x) or controlled by the remote system with a 0 Vdc

respectively on the “Led 1”, “Led 2” and “Buzzer” inputs of the reader’s connector or controlled by the communication protocol of the reader (W3x).

Anti-tearing

Tearing is detected by an accelerometer. When the reader is wrenched, the switch output (connector J2) provides an O/C contact to indicate the tearing of

reader.

▪ for R/S 31/x1: the wrenching signal will be emitted on the “Data/Data1” line. This function is configurable via a configuration card.

▪ for R/S 32/33/x2/x3 and OSDP

: the reader will perform the operations configured with the configuration card.

▪ for W 32/33/x2/x3: the reader will perform the operations configured with the SSCP protocol.

Caution: switch on the reader when it is in its final position to initialize the accelerometer in the correct position.

Relay

Read-only reader: automatic tamper management (except touch screen) or activated on the reading of a valid identifier

Touch screen read-only reader: if the bell is activated, contact J2 is used to connect the external ring (max. 200 mA at 28 Vdc).

Read/Write & OSDP

readers: the relay is controlled by the SSCP/ OSDP

protocol commands.

UHF default configuration settings

Reader powered off. The defaults reader settings can be stored in internal memory accessible by UHF RFID technology. They will be taken into account when

the reader is powered on.

Read-only reader configuration

R and S readers are configurable with the SCB configuration card created with SECard. OSDP

readers are configurable with OCB configuration card:

▪ If the SCB/OCB is compatible with the reader’s firmware, the LED lights green and the buzzer beeps five times.

▪ If the SCB/OCB is not compatible with the reader’s firmware, the LED lights red and the buzzer is activated for 1 s.

▪ If the SCB/OCB key is different from the reader’s key: no reaction.

Caution: set your reader with your own company key.

Powering-up the readers

On power-up, the reader enters an initialization phase:

1. Activation of the white LED and buzzer for 100 ms.

For read-only and OSDP

readers:

2. Activation of the LED, according to the color code: Red = +10, Orange = +5, Green = +1, indicating the firmware version.

3. For serial R/S ARC only: the orange LED flashes 20 times: waiting for an update.

4. Activation of the default LED (read-only: flashes blue, OSDP

: off; if no customer specific configuration).

5. ARC Screen: display of the default image and keypad activation by touching the screen.

For the ARC screen with an activated keypad, the default mode is displaying the picture on standby and activate the keyboard by pressing the screen.

Precautions for the biometric sensor and keypad

▪ For optimal operation, the biometric sensor must be free of all traces of water. Outdoors it is recommended to install the reader under cover.

▪ The keypad is sensitive. Take off your gloves to enter your code.

ARC-X

A: Standard

B: Keypad

C: Touch screen

D: Standard + Biometrics

E: Keypad + Biometrics

F: Touch screen + Biometrics

I : Standard + 125 kHz module

J : Keypad + 125 kHz module

K : Touch screen + 125 kHz module

AQ: Standard + QR Code module

BQ: Keypad + QR Code module

CQ: Touch Screen + QR Code module

J6: Antenna connector

J7: Keypad connector

J9: Biometric connector

J14: Display connector

J2: O/C contact

Connector

Type

Wiegand

Clock & Data

RS232

RS485

0 Vdc

+Vcc (+7 Vdc to +28 Vdc)

Code

Data

Clock

L+

L-

Led 1

Led 2

Buzzer