UB-2PN Universal 2” Pneumatic Button ADA for operation We protect the things that protect you.
NOTES It is important to read, understand and follow all instructions provided with this product. It is the installer’s responsibility to comply with NFPA 70 & 101, NEC, mounting specifications according to ADA and other applicable electrical codes.This switch is rated Type NM (Non-Monitored) for nonemergency signaling. Not to be used in place of panic hardware. To avoid electrical shock, DO NOT attempt to install this product when power is on.
1 TO CHANGE BUTTON COLOR AND ROUND MESSAGE REAR VIEW ALIGN TAB ON ACTUATOR WITH SLOT BUTTON. TURN CLOCKWISE TO LOCK INSERT ASSEMBLY WITH SPRING INTO PLATE. PUSH BUTTON ACTUATOR BUT 1 SPRING DIE CAST PLATE 2 in. BUTTON ACTUATOR CAP 2 1 1. Choose button message and color. If same as existing, proceed to 2 2. To remove push button actuator assembly, squeeze actuator tabs in direction of #1 arrows. 3. Push acutator through plate in direction of #2 arrow. 4. Align actuator cap to push button actuator.
3 INSTALL OR REMOVE CONTACT BLOCK BUTTON ACTIVATED M BUTTON ACTIVATED M PO 12-3 WER 0 V IN DC/ VAC INSTALL To attach, align tabs (as shown) and gently snap top, then bottom. Be sure to hear BOTH tabs snap into place. Contacts can be rotated 180° if desired. CONTACT INFORMATION POWER IN 12-30 VDC/VAC POWER IN 12-30 VDC/VAC CONTACT REMOVAL A DETAIL A -4- REMOVE To remove, use a small flat blade screwdriver. Position screwdriver blade under tab and gently rotate screwdriver until tab disengages.
4 ATTACH POWER FOR LED (IF DESIRED) (See drawing) MAG LOCK + NC CONTACTS NO CONTACTS + UB-1L LED PCB + UL Listed 12-24 VDC Power Supply NORMAL POSITION BUTTON ACTIVATED MAGNETIC LOCK ON OFF MESSAGE LAMP OFF ON CONTACT DIAGRAM NC (GREEN) (BLACK) NC NO (WHITE) (RED) NO CONTACTS One set NO and one set NC NC NC NO NO -5-
SWITCH INFORMATION COUNTERCLOCKWISE CLOCKWISE TIMER RANGE ADJUSTMENT SCREW ADJUSTMENT RANGE - 2 TO 60 SECONDS TIMER FACTORY SET TO MINIMUM TIME SETTING. TO INCREASE TIME, TURN SCREW CLOCKWISE IN 1/4 TURN INCREMENTS. WHEN CLOSE TO DESIRED TIME, TURN SCREW IN VERY FINE INCREMENTS TO DESIRED SETTING. CAUTION: OVER-TIGHTENING MAY CAUSE DAMAGE TO TIMER. 5 MOUNT BUTTON ONTO ELECTRICAL BOX 6 CUSTOM LABELS To create your own custom label, size to fit in .48h x 2.23w as shown below. Also available online at: www.
ACCESSORIES DESCRIPTION CONTACT BLOCK COLOR MATCH BACK BOX KIT CUSTOM LABEL APPLIED TO BLANK MESSAGE PLATES PART # SUB-UB-1PNC SUB-71100A-COLOR (red, blue, green, white or yellow) UB-1CL-COLOR (blue, green, white or yellow) 24 VOLT LED WHITE (STANDARD) RED BLUE GREEN 10147 10145 10141 10143 12 VOLT LED RED BLUE GREEN 10144 10140 10142 COVERS BOPPER STOPPER UNIVERSAL STOPPER STOPPER II STI-6518 STI-13000 Series STI-1100 Series See website for complete cover details -7-
WARRANTY Three year guarantee against breakage of polycarbonate in normal use (one year on electro mechanical and electronic components). Electronic warranty form at www.sti-usa.com/wc14. 2306 Airport Rd • Waterford, MI 48327 Phone: 248-673-9898 • Fax: 248-673-1246 info@sti-usa.com • www.sti-usa.com Safety Technology International (Europe) Ltd.
