Installation Instructions

Strike
Side
24-7/8"
(632 mm)
120˚
Right Pivot
Left Pivot
120˚
Strike Side Only
1" (25 mm) Gap
1" (25 mm) Gap
Bulb Seal
Slots to
the inside.
x2
Screws
#8-18 x 1-1/2"
x2
3
1
2
3/4" (19 mm)
3/4" (19 mm)
Connector
Block
Nut
Lay flat.
Lay flat.
Screw
Nut
Connector Block
#8-32 x 1"
x4
Mark
x2
Level
Wall Jamb
1" (25 mm)
Only drill through the inside
wall.
1/8"
Inside of
Shower
x6
x6
x2
Wall Jamb
#8-18 x 1/2"
100% Silicone Sealant
Hex Wrench
Assorted Drill Bits
Masking Tape
Neo-Angle Shower Doors
Hinge Skin Pack
1160603**
Hinge Assembly
1158712-01**
Hardware Skin Pack
1098896**
Setscrew
1160604
Bridge Member
1109490-01**
#8-18 x 1/2"
#8-18 x 1/2"
#8-18 x 1/2"
#8-18 x 1/2"
#8-18 x 1/2"
#8-32 x 1"
#8-32 x 1"
#8-32 x 1"
#8-32 x 1"
#8-32 x 3/8"
#8-18 x 1-1/2"
Screw
1048208-C
Screw
1042520-E
Screw
1042520-E
Nut
1052901-A
Connector Block
1172133
Screw
1042862-E
Pivot Pin
1097909
Screw
1042862-E
Connector Block
1172133
Wall Jamb
1082128-01**
Hinge Plate
1112301**
Sleeve
1013445
Screw
1042871-A
Plug
1088418
Screw
1042520-E
Jamb Seal
1089071-01**
Screw
1042520-E
Fixed Panel
1085684-02**
Jamb Seal
1089071-01**
Door Panel
1075279-01**
Bulb Seal
1096489**
Nut
1052901-A
Screw
1042862-E
Plug
1088418
Screw
1042862-E
Nut
1052901-A
Connector Block
1172133
Nylon Washer
1052892-A
Pivot Pin
1097910
Threshold Seal
1014086-02
Connector Block
1172133
Bridge Member
1109490-01**
Fixed Panel
1085684-02**
Handle Assembly
1019899*
Hinge Assembly
1158712-01**
Hinge Gasket
1101374
Nut
1052901-A
Screw
1042520-E
Anchor
1077762
Wall Jamb
1082128-01**
1
1178458-2-B
USA: 1-800-STERLING (1-800-783-7546)
Mexico: 001-877-680-1310
SterlingPlumbing.com
1178458-2-B
Installation Guide
SP2375 Series Neo-Angle Shower Doors
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
1
Required Tools
Parts Identification
2
7
3
8654
CAUTION: Risk of injury or property damage.
Do not attempt to cut tempered glass.
Walls must be within 3/8” (10 mm) of plumb.
Cover drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer’s instructions
for application and curing time.
This shower door is designed to be paired with a
Sterling shower module. Check the specifications to use
this door with other installations.
The shower enclosure and finished wall material
should be installed before beginning the shower door
installation.
The shower door can be installed with the door opening
to either the right or left. Install the door with the pivot
side away from the showerhead for best results.
Determine whether the door will swing to the
right or the left.
NOTE: The illustrations and instructions in
this guide are for a right-pivot door. Left-
pivot installations will be opposite of what is
illustrated unless specific directions are given.
Mark the location of the wall jambs. The front
edge should be 3/4” (19 mm) from the front
edge of the threshold.
Align the front edge of the wall jambs with the
marks. Plumb the wall jambs. Mark the wall-
jamb holes.
Remove the wall jambs. Drill 5/16” holes into
the walls and insert the anchors.
Reposition both wall jambs, slots to the inside of
the shower. Use three screws to secure each wall
jamb.
Trim the bulb seal to be 2” (51 mm) shorter than
the length of the panels. On the strike side only
(opposite the pivot), slide the bulb seal into the
slot. Center the bulb seal vertically with a 1” (25
mm) gap at the top and bottom.
At the top and bottom of each panel, insert a
connector-block tab into each of the four fixed-
panel grooves. Secure each connector block with
a screw and nut.
Slide the strike and pivot panels into the wall
jambs. Confirm the panels are correctly located.
From inside, mark the wall jamb slot at the top,
bottom, and center. Drill at the marks. Loosely
attach the panels.