Installation Instructions

11187937-2-A
Required Tools
Parts Identification
SP2270 Series Neo-Angle Shower Doors
9
2
3
1
USA: 1-800-STERLING (1-800-783-7546)
Mexico: 001-877-680-1310
SterlingPlumbing.com
Installation Guide
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
Screw
1049018-K
1049018-J
(Brass)
(Silver)
1049018-S (Black)
Wall Jamb
681545
681544
681511
(Brass)
681501
(Silver)
681546
(Deep Bronze)
(Nickel)
(Matte Silver)
682038
682011
682001
(Silver)
(Brass)
(Nickel)
Column
682039
(Matte Silver)
684030
684010
684001
(Silver)
682040
(Deep Bronze)
684032
(Deep Bronze)
(Brass)
(Nickel)
Flange (Includes Seal 521311)
684031
(Matte Silver)
684130
684110
684101
(Silver)
684132
(Deep Bronze)
(Brass)
(Nickel)
Strike Post (Includes Magnet 681200)
684131
(Matte Silver)
Pivot Pin
1088416
Bushing
1088417
Washer
1052892-A
Seal
521307
Seal
521307
Seal
521311
Magnet
681200
Magnet
681301
Panel Cushion
1088771
Plug
1088418
Screw
1048208-A
Anchor
1077762
Screw
1031659-C
Screw
1031659-C
Side Panel*
Side Panel*
Door Panel*
(Includes Magnet 681301)
Screw
1049018-L
1049018-D
(Brass)
(Silver)
1049018-T (Black)
Bridge Member (Includes Seal 521307)
919933
919932
919919
(Brass)
919918
(Silver)
919934
(Deep Bronze)
(Nickel)
(Matte Silver)
Series
Number Label
Adjustment Block
1031813
Wall Jamb
681545
681544
681511
(Brass)
681501
(Silver)
681546
(Deep Bronze)
(Nickel)
(Matte Silver)
682038
682011
682001
(Silver)
(Brass)
(Nickel)
Column
682039
(Matte Silver)
682040
(Deep Bronze)
Pivot Pin
1088416
Bushing
1088417
1080993**
Hardware Pack
Neo-Angle Shower Doors
Assorted Drill Bits
100% Silicone Sealant Masking Tape
Tin Snips
#8-18 x
1-3/4"
Screws
Front
Edge
2
1
3
x2
x2
Pencil
Wall Jamb
Level
3/4"
(19 mm)
Slide an adjustment block (4) onto each end of the
wall jambs, positioned over the first hole. Secure
in place with tape. Loosen the adjustment in each
adjustment block until it extends 1/2" (13 mm).
Move a wall jamb into place with the sealant
groove against the wall, toward the outside of the
shower, Secure with three screws. Repeat for
other side.
CAUTION: Risk of injury or property damage.
Do not attempt to cut tempered glass.
Walls must be within 3/8" (10 mm) of plumb.
Cover drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's
instructions for application and curing time.
This shower door is designed to be paired with a
Sterling shower module. Check the specifications
to use this door with other installations.
Mark the location of the wall jambs. The front
edge should be 3/4" (19 mm) from the front
edge of the threshold.
Move the wall jambs into place and check the fit.
When needed, snip and file the bottom edges of
the wall jambs for a snug fit.
Apply a bead of silicone sealant to the groove
along the entire wall jamb.
Align the front edge of the wall jambs with the
marks. Plumb the wall jambs. Mark the front
edges of the wall jambs and the wall-jamb holes.
3/4"
(19 mm)
Front
Edge
Front
Edge
Front
Edge
Tape
1/2"
(13 mm)
Silicone Sealant
Front Edge
Front
Edge
Wall Jamb
4
7
5
6
8
Wall Jamb
Expander Jamb
x2
Use a screwdriver to tighten or loosen the
adjustment blocks until they firmly and evenly
contact the wall frame.
Carefully lift the side panels onto the shower
ledge. Align the expander jamb on the panel with
the wall jamb.
Remove the wall jambs. Lay both wall jambs
down on a flat surface. Drill 5/16" holes at each
mark on the walls. Insert an anchor in each hole.
x2
Expander
Jamb
Adjustment Block
5/16" Drill
Bit