RSD Series Brochure

3
MODEL
HORIZONTAL
35° ANGLE
STANDARD REFLECTOR W/ PARABOLIC EXTENSION STANDARD REFLECTOR W/ PARABOLIC EXTENSION
RSD30 RSD33
11 12 10 12
RSD35 RSD40 12 13 11 13
RSD60 RSD66 RSD70 13 15 12 14
RSD80 14 16 13 15
RSD100 15 17 14 16
RSD120 16 18 15 17
RSD132 RSD140
17 19 16 18
RSD160 18 20 17 19
MODEL
HORIZONTAL 35° ANGLE
ANGLE MTG.
(DEGREE)SIDES CEILING
BELOW BELOW FRONT
REAR (35°)
STANDARD
REFLECTOR
W/ PARABOLIC
EXTENSION
STANDARD
REFLECTOR
W/ PARABOLIC
EXTENSION
STANDARD
REFLECTOR
W/ PARABOLIC
EXTENSION
RSD30 RSD35 RSD33 RSD40 30" 36" 72" 100" 72" 100" 36" 50" 30" 0 min/35 max
RSD60 RSD70 RSD66 RSD80 48" 48" 98" 137" 98" 137" 48" 68" 36" 0 min/35 max
RSD100 RSD120
48" 64" 128" 180" 128" 180" 60" 84" 48" 0 min/35 max
RSD132 RSD160 RSD140
60" 64" 136" 190" 136" 190" 64" 90" 48" 10 min/35 max
RSD SERIES ARCHITECHTURAL/ENGINEERING SHORT FORM SPECIFICATIONS
Gas-Fired infrared space heaters shall be furnished and installed in accordance with governing codes and as shown per building
drawing(s) as described below: Heaters shall be RSD series ceramic heaters, model number(s) RSD ________ , ________ Btu/hr, as
manufactured. Heaters shall be equipped with a 24V direct spark ignition system with 100% gas shutoff.
Heaters shall be made of aluminized steel body construction and shall consist of multiple burner heads. Heaters shall utilize
special honeycomb tile design for increased radiant output. As an option, heaters can utilize an Incoloy 800 reverberatory
screen that will increase the overall emissivity of the radiant surface with a black body radiation effect and could serve as a
protective screen in the unlikely event that the ceramic tile assembly is broken by an outside force. The tile temperatures can
vary from 1650°F-1800°F and tiles shall withstand thermal shock when water quenched.
Heaters shall operate satisfactorily in any position from horizontal to thirty five degrees from horizontal. Heaters shall be Design Certified
by C.S.A. to American National Standard Z83.19 /CSA Standard 2.35. The manufacturer shall provide a written limited warranty of five (5)
years covering the emitter tiles and a limited warranty of one (1) year for all components utilized in the heater’s control assembly.
Mounting Height
Ceramic heaters may be mounted at various heights and angles, according to the results desired. Please consult your
representative for your radiant heating requirements. Observe all required clearances to combustibles shown above.
Combustion Air and Ventilation
Combustion air and venting requirements for all gas-fired heating equipment must be provided per National Fuel Gas Code
NFPA54, CAN B149 or the authority having jurisdiction over the installation. Indirect vented ceramic heaters require a
minimum ventilation flow of 4 CFM per 1000 Btu per hour of total installed heater capacity on natural gas by either gravity or
power ventilation (4.18 CFM per 1000 Btu per hour on propane). For more ventilation information, consult the ASHRAE
handbooks, local codes, and the Application Manual. Building exhaust openings for indirect vented applications always
must be located above the level of the heaters and inlet air openings always must be located below the level of the heaters.
For Your Safety
OPERATE INFRARED HEATERS WITH PROPER CARE AND OBSERVE ALL SAFETY PRECAUTIONS. Carefully follow the printed
installation, operation, and cleaning instructions furnished with these heaters. Follow the instructions on the nameplate of
each heater and use in accordance with National, State, and Local Codes or the authority having jurisdiction. Adequate
ventilation always must be provided in accordance with the codes.
Observe all required clearances as shown. Clearances are measured from the reflector edge.
RSD MOUNTING HEIGHTS, CLEARANCES & DIMENSIONS
RSD30 RSD33
RSD35 RSD40
RSD60 RSD66
RSD70 RSD80
RSD100
RSD120
RSD132
RSD140
RSD160
RSD30 RSD33
RSD35 RSD40
RSD60 RSD66
RSD70 RSD80
RSD100
RSD120
RSD132
RSD140
RSD160
END VIEW DIMENSIONS END VIEW DIMENSIONS
Minumum Recommended Mounting Heights (Feet)
Minimum Clearances To Combustibles