Installation Sheet

ManualsBrandsSTERLING ManualsAlcove Shower DoorsStandard 48 in. x 65 in. Framed Sliding Shower Door in Silver

Large Leg

to Outside

Groove

3/16" Diameter Holes

3" (76 mm)

#6-32 x 5/16"

To Outside

100% Silicone Sealant

Masking Tape

32 Teeth Per Inch Blade

1/8", 3/16", 5/16", 5/16" Masonry

Miter Box

Tin Snips

Long Leg

Wall Jamb*

Towel Bar Bracket and Hardware

1173259**

Towel Bar

Outside Panel*

Cover

1129873

Bottom Track

1129841-01**

Guide

1083114**

Tape

1129843-01

Wall Jamb*

Bumper

172821

Top Track

Long Leg

Wall Jamb

Handle

1171024-01**

Top Track

1129847-01**

Screw

#8-32 x 3/8"

1042862-A

Towel Bar*

Inside Panel*

Screw

# 8-18 x 3/8"

1049018-G

Hardware Skin Pack

1173290**

Screw

#6-32 x 5/16"

1042930-A

Roller

172818

Bracket

1171026-01**

Screw

#8-18 x 1-1/4"

1048208-E

Anchor

1077762

Series Number Label

1130696-01**

Tapered

Wall Jamb

Tapered Wall Jamb

Non Tapered Wall Jamb

NOTE: If installing the 660SP series door to a 48” (1219

mm) Sterling 6203 series shower unit, cut the bottom

track to 42-1/4” (1073 mm). If installing the 660SP series

door to a 60” (1524 mm) Sterling 6204 series shower

unit, cut the bottom track to 54-1/4” (1378 mm).

NOTE: For all other installations, measure distance “A“

and cut the bottom track.

IMPORTANT! This shower door includes two sets

of wall jambs, tapered and non-tapered. If you are

installing the door to a Sterling shower unit, use the

tapered set. For all other bath units, use the non-tapered

set.

NOTE: This installation is shown with non-tapered wall

jambs.

File the bottom track edges to fit curved corners

of the shower or bath unit.

Measure and mark the exact center of the bottom

track. Center the guide and mark the hole.

Drill a 1/8” hole at the marked location and

attach the guide with a #6-32 x 5/16” flathead

screw.

Center the bottom track on the ledge with the

leg to the outside. Tape in place and mark the

position.

Position the wall jamb with the “groove” side up.

Drill a 3/16” hole 3” (76 mm) from each end and

one in the center between the two holes.

Position the wall jambs over the bottom track.

Snip/file bottom edges for a snug fit.

Plumb both wall jambs. Mark the screw holes.

NOTE: If tapered wall jambs are used, the

tapered area should be located on the threshold,

with the taper against the wall.

660SP Series Sliding Shower and Bath Doors

11241257-2-B

USA/Canada: 1-800-STERLING (1-800-783-7546)

México: 001-877-680-1310

1241257-2-B

Installation and Care Instructions

Required Tools Parts Identiﬁ cation

4 53 6

SterlingPlumbing.com

*Need help? Contact the STERLING Customer Care Center

at 1-800-STERLING (1-800-783-7546).

For service parts information, care and cleaning, and

other information, visit www.sterlingplumbing.com

**Finish/color code must be speciﬁ ed when ordering.

Retain this document for future servicing.

Record model number from box for reference.

Model Number:______________

WARNING: Risk of serious injury. Damage prior to installation can

result in glass shattering. Inspect the glass and all parts for damage

before installation.

WARNING: Risk of serious injury. Improper installation can result

in glass shattering. Follow all installation instructions.

WARNING: Risk of serious injury. Do not cut tempered glass.

Tempered glass will shatter if cut.

WARNING: Risk of serious injury. Shower door and side panels

can shatter. Regularly inspect the glass and all parts for damage,

missing, or loose parts.

WARNING: Risk of serious injury. Always wear safety glasses

while cutting and drilling.

IMPORTANT! Do not touch the edges of the tempered glass with tools or

any other hard objects. Do not set the unframed tempered glass directly on

the floor or any hard surface.

IMPORTANT! Leave this manual for the end user.

Read these instructions before installing or using this product.

IMPORTANT! Do not cut the top track the same length as the bottom track.

NOTICE: The warranty does not apply to a product that has been modified

or altered in a manner other than as expressly permitted in the Installation

and Care Guide.

Walls must be within 3/8” (10 mm) of plumb.

Cover the drain with tape to avoid loss of small parts.

Follow the silicone sealant manufacturer’s instructions for application and

curing time.

To watch this installation online, visit the product page at

www.sterlingplumbing.com.

For care and cleaning and other information; visit

www.sterlingplumbing.com/care-and-cleaning.

Critical Information!

Read Before Installation!

Read and follow all instructions.

Summary of content (6 pages)

PAGE 1
Installation and Care Instructions 660SP Series Sliding Shower and Bath Doors 1241257-2-B Required Tools Parts Identification *Need help? Contact the STERLING Customer Care Center at 1-800-STERLING (1-800-783-7546). For service parts information, care and cleaning, and other information, visit www.sterlingplumbing.com **Finish/color code must be specified when ordering. Retain this document for future servicing. Record model number from box for reference.
PAGE 2
8 Remove the wall jambs. Drill 5/16” holes into the walls and insert the anchors. 9 Secure both wall jambs with screws. Attach a bumper to the top and bottom location. NOTE: Use #8-18 x 2” panhead screws for tapered wall jambs. 10 Measure distance “B” above the jambs. Subtract 1/32” (1 mm) from “B” and cut the top track. 11 Position the top track over the wall jambs. 12 Assemble the inside panel rollers by positioning them in the middle of the slot.
PAGE 3
Instructions d'installation et d'entretien Portes de douche et de baignoire coulissantes Série 660SP 1241257-2-B Outils requis Identification des pièces *Besoin d'aide? Appeler le centre de services à la clientèle de STERLING au 1-800-STERLING (1-800-783-7546). Pour tout renseignement sur les pièces de rechange, l'entretien, le nettoyage, et autre, visiter le site www.sterlingplumbing.com. **Les codes de finition et/ou de couleur doivent être fournis au moment de la commande.
PAGE 4
8 Retirer les montants de murs. Percer des trous de 5/16" dans les murs et insérer les chevilles d'ancrage. 9 Sécuriser les deux montants de mur avec des vis. Fixer une butée sur les emplacements supérieur et inférieur. REMARQUE: Utiliser des vis à tête cylindrique bombée #8-18 x 2” pour des montants de mur effilés. 10 Mesurer la distance “B” au-dessus des montants. Soustraire 1/32” (1 mm) de “B” et couper le rail supérieur. 11 Positionner le rail supérieur sur les montants de mur.
PAGE 5
Instrucciones de instalación y cuidado Puertas corredizas de bañera y ducha Serie 660SP 1241257-2-B Herramientas requeridas Identificación de piezas *¿Necesita ayuda? Comuníquese con el Centro de Atención al Cliente de STERLING al 1-800-STERLING (1-800-783-7546). Para obtener información acerca de piezas de repuesto, cuidado y limpieza, y otro tipo de información, visite www.sterlingplumbing.com. **Se debe especificar el código del acabado/color con el pedido. Guarde este documento para servicio futuro.
PAGE 6
8 Retire las jambas murales. Taladre orificios de 5/16" en las paredes e introduzca los anclajes. 9 Fije ambas jambas murales con tornillos. Fije un tope en las ubicaciones superior e inferior. NOTA: Use tornillos de cabeza redonda #8-18 x 2” en las jambas murales angulares. 10 Mida la distancia “B” sobre las jambas. Reste 1/32" (1 mm) de la dimensión “B” y corte el carril superior. 11 Coloque el carril superior sobre las jambas murales.