Installation Guide

ManualsBrandsSTERLING ManualsAlcove Shower DoorsFinesse 36-1/2 in. x 65-1/2 in. Semi-Frameless Pivot Shower Door in Silver

Adjustment

Clamps to the

Inside of the

Shower

Tall Side of the

Bottom Track

Stop

Showerhead

Wall Jamb

Outside

Stop

Level

#8-18 x 1-1/2"

Level

Wall

Jamb

Bottom

Track

Front Side

of Bottom

Track

Tin Snips

Miter Box

32 Teeth Per Inch Blade

Masking Tape

100% Silicone Sealant

5/16" 5/16" Masonry Bit for Tile

Clamp

Screw

Bottom Track

Continuous Hinge

Handle

Latch

Hex Wrench

Series

Number Label

Panhead Screw

Hinge Jamb

Hinge Jamb Cover

1019386-A

Screw

1019387-C

(Silver)

1048208-B

Door Panel

Assembly*

Threshold Seal*

(Black)

(Silver)

(3/32")

(5/64")1013942

1019972

1019899**

S11236.07

S11236.01

1013641-01**

1019386-C

1017115**

Strike Jamb

1014081-01**

1019387-A

867201

1019934-01**

1018459**

Strike Jamb Cover

1019420**

Bulb Seal

1021020

Wall Anchor

Screw

LH Wall Jamb Cover

1048208-N

1077762

1022735

(Silver)

(Black)

1019310**

Hardware Pack

Wall Jamb

1022737-01**

RH Wall Jamb Cover

1022734

(Black)

(Silver)

Adjustment Clamp

Wall Jamb

#8-18 x 3/4"

Showerhead

Strike Side

Showerhead

Strike Side

Right Pivot Left Pivot

Handle

Pivot Side

Handle

Pivot Side

Determine either a right or a left door pivot.

The door handle installs on the same side as the

showerhead.

Loosely attach four adjustment clamps to each

wall jamb with flathead screws. Use the hex

wrench provided. Do not tighten the screws at

this time.

Center the wall jambs on the threshold and check

the fit. If needed, snip and file the bottom edges

of the wall jambs for a snug fit.

Using a level, plumb both wall jambs. Secure

with masking tape. Mark the screw holes and the

front edges of the wall jambs.

Remove the wall jambs. Drill 5/16” holes and

insert anchors in both shower walls. For tile, use

a 5/16” tile bit. Anchors will work in wall studs.

Realign and plumb both wall jambs. Secure with

screws.

At the threshold, measure from the first stop on

the inside of the strike wall jamb to the first stop

on the inside of the hinge wall jamb (Dimension

“A”).

Cut the bottom track to dimension “A.” Smooth

the cut edge with a file. Verify bottom track fit

between the wall jambs so the tall side of the

bottom track is to the outside.

Apply silicone sealant along the groove on the

underside of the bottom track.

Position the bottom track on the threshold and

between the first steps of the wall jambs. Make

sure the tall side of the bottom track faces out.

Tape the bottom track in place.

6300 Hinge Shower Doors

IMPORTANT! Do not cut the top track the same length as the bottom track.

Walls must be within 3/8” (10 mm) of plumb.

Cover the drain with tape to avoid loss of small parts.

Follow the silicone sealant manufacturer’s instructions for application and

curing time.

For care and cleaning and other information; visit

www.sterlingplumbing.com/care-and-cleaning.

Hinge Shower Doors

11190302-2-C

USA/Canada: 1-800-STERLING (1-800-783-7546)

México: 001-877-680-1310

1190302-2-C

Installation and Care Instructions

*Call Customer Care Center to order replacement parts.

**Finish/color code must be speciﬁ ed when ordering.

Retain this document for future servicing.

Record model number from box for reference.

Model Number:______________

Required Tools Parts Identiﬁ cation

2 3 4

7 86 9

1 5

WARNING: Risk of serious injury. Damage prior to installation can

result in glass shattering. Inspect the glass and all parts for damage

before installation.

WARNING: Risk of serious injury. Improper installation can result

in glass shattering. Follow all installation instructions.

WARNING: Risk of serious injury. Do not cut tempered glass.

Tempered glass will shatter if cut.

WARNING: Risk of serious injury. Shower door and side panels

can shatter. Regularly inspect the glass and all parts for damage,

missing, or loose parts.

WARNING: Risk of serious injury. Always wear safety glasses

while cutting and drilling.

NOTICE: Do not touch the edges of the tempered glass with tools or any

other hard objects. Do not set the unframed tempered glass directly on the

floor or any hard surface.

IMPORTANT! Leave this manual for the end user.

Read these instructions before installing or using this product.

SterlingPlumbing.com

Summary of content (6 pages)

PAGE 1
Installation and Care Instructions 6300 Hinge Shower Doors 1190302-2-C Required Tools *Call Customer Care Center to order replacement parts. **Finish/color code must be specified when ordering. Retain this document for future servicing. Record model number from box for reference. Parts Identification 1019310** Hardware Pack Model Number:______________ Hinge Shower Doors USA/Canada: 1-800-STERLING (1-800-783-7546) México: 001-877-680-1310 SterlingPlumbing.com WARNING: Risk of serious injury.
PAGE 2
11 Lay the hinge jamb on a flat, protected surface. Insert the unslotted wing of the hinge into the hinge jamb groove. Use four screws to secure the hinge to the hinge jamb. 12 Align the hinge assembly even with the top of the channel. Secure the hinge to the door panel with the panhead screws. Install the hinge jamb cover to the hinge jamb. 13 Lay the door panel on a flat, protected surface. Starting at the hinge end of the glass, press the threshold seal onto the bottom of the door panel.
PAGE 3
Instructions d'installation et d'entretien Portes de douche à charnière 6300 1190302-2-C Outils requis *Appeler le service d'assistance à la clientèle pour commander des pièces de rechange. **Les codes de finition et/ou de couleur doivent être fournis au moment de la commande. Conserver ce document pour référence. Noter le numéro de modèle sur le carton d'emballage à titre de référence. Identification des pièces 1019310** Quincaillerie Nº du modèle:______________ Portes de douche à charnière É.-U.
PAGE 4
11 Poser le montant à charnière sur une surface plate et protégée. Insérer l'aile sans fentes de la charnière dans la rainure du montant à charnière. Utiliser quatre vis pour sécuriser la charnière sur le montant à charnière. 12 Aligner l'ensemble à charnière à égalité avec le dessus du canal. Fixer la charnière au panneau de la porte en utilisant les vis à tête cylindrique. Installer le couvercle du montant à charnière sur le montant à charnière.
PAGE 5
Instrucciones de instalación y cuidado Puertas de ducha con bisagra 6300 1190302-2-C Herramientas requeridas *Llame al Centro de Atención al Cliente para pedir piezas de repuesto. **Se debe especificar el código del acabado/color con el pedido. Guarde este documento para servicio futuro. Apunte el número de modelo de la caja para referencia. Identificación de piezas 1019310** Paquete de herrajes Número de modelo:______________ Puertas de ducha con bisagra EE.UU.
PAGE 6
11 Coloque la jamba de bisagra sobre una superficie plana y con protección. Inserte el ala sin ranura de la bisagra en la ranura de la jamba de bisagra. Utilice cuatro tornillos para fijar la bisagra de la jamba de bisagra. 12 Alinee el montaje de bisagra parejo con la parte superior del canal. Fije la bisagra al panel de la puerta con tornillos de cabeza redonda. Instale la tapa de la jamba de bisagra en la jamba de bisagra. 13 Coloque el panel de puerta sobre una superficie plana y con protección.