Installation Instructions

ManualsBrandsSterling ManualsBathtub Doors5407-59N-G05

21 22

Lift the outside panel onto the outside track. The

label faces the outside of the shower.

If either panel needs adjustment, remove the door

and position the rollers in new holes to raise or

lower the glass.

Measure and mark the center of the bottom track.

Center the guide on the bottom track and align

the door panels with the guide.

On the inside of the shower, hold the guide

against the bottom track and slide the doors from

wall to wall. If the doors bind, refer to step 18 for

the adjustment procedure.

Outside the shower, use silicone sealant to seal

along the entire length of the wall jambs and the

bottom track.

Inside the shower, use silicone sealant to seal

along the entire length of the wall jambs and

where the wall jambs meet the bottom track.

Position the top track over the wall jambs. Either

side of the top track may face out.

For both doors, insert a bushing into each hole at

the top of the glass panels. Install the hanger

brackets over the glass panels. Align the hanger

brackets with the mounting holes.

Insert a blind nut through each hanger bracket

and bushing. Secure with a sex bolt. Use a

screwdriver to tighten the sex bolts. Do not

overtighten!

1312

1183935-2-A

TROUBLESHOOTING

WARRANTY

5 YEARS LIMITED

5100 Series, 5300 Series, 5400 Series, 6300 Series, 6500 Series

3 YEARS LIMITED

1500 Series, 1900 Series, 2200 Series, 5900 Series

1 YEAR LIMITED

500 Series, 600 Series, 660 Series, 670 Series, 690 Series, 950 Series, 2300 Series

Based on the classification specified above, STERLING bath and shower doors are warranted to be free of

manufacturing defects within the time of the specified model’s limited warranty from date of sale.

Kohler Co. will, at its election, repair, rectify or replace a fixture when inspection by Kohler Co. discloses any such

defects occurring in normal usage within the time period of coverage stated above. Kohler Co. is not responsible for

removal or installation costs where replacement is indicated. Damages due to improper handling, installation or

maintenance are not considered manufacturing defects and are not covered by this warranty. This warranty is valid

for the original, consumer purchaser only.

To obtain warranty service, contact Sterling, either through your plumbing contractor, home center, wholesaler or

dealer, or by calling or writing Sterling, Consumer Services, 444 Highland Drive, Kohler, Wisconsin 53044,

1-800-783-7546.

TO THE EXTENT PERMITTED BY LAW, ALL IMPLIED WARRANTIES INCLUDING THOSE OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.

KOHLER CO. AND SELLER HEREBY DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES. Some states/provinces do not allow limitations on how long an implied warranty

lasts, or the exclusion or limitation of special, incidental or consequential damages, so these limitations and

exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights

which vary from state/province to state/province.

This is the exclusive written warranty for Kohler Co.

Symptom: Alignment

1. The top of the door panel is tilted away from the

wall.

2. The bottom of the door panel is tilted away from

the wall.

3. The door panel does not touch the bumper.

4. The bottom track is miscut or skewed.

Symptom: Water Leaks

1. Water leaks between panels.

2. Water leaks between the wall jamb and

the door panel.

3. Water leaks under the bottom track.

Symptom: Operation (open/close)

1. The outside panel is difficult to move.

2. The inside panel is difficult to move.

Recommended Action

A. Remove the door panel from the top track and lower the roller that is closest to the wall. See step 18.

A. Remove the door panel from the top track and raise the roller that is closest to the wall. See step 18.

A. Determine whether the door panel top or bottom is closer to the wall, and then adjust the roller closest to the wall.

A. The notched wall jamb fits over the bottom track to cover any miscut or skewed cuts. Seal as directed to ensure

proper watertight seal. See step 24.

Recommended Action

A. When showering, make sure the inside panel is against the showerhead wall.

A. Adjust the door panel to line up with the wall jamb.

A. Check for proper silicone sealant application. See steps 23 and 24. Apply more silicone sealant in the leak location.

Recommended Action

A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next hole.

B. Ensure the panel is properly engaged over the bottom track. See steps 16 and 17.

C. Ensure the rollers are properly installed. See steps 14 and 15.

D. Clean any debris in the top track groove.

A. Ensure a gap exists between the bottom track and the door panel. If no gap exists, lower the rollers to the next hole.

B. Ensure the inside center guide is properly secured with the self-tapping screws. See step 21.

C. Ensure the rollers are properly installed. See steps 16 and 17.

D. Clean any debris in the top track groove.

Reversible

Bushing

Blind Nut

Lower the glass.

Raise the glass.

Hanger

Bracket

Bottom Track

Guide

Center of the

Bottom Track

Sex Bolt

Hanger

Bracket

Hold the guide in place and secure with the two

self-tapping screws. Do not overtighten!

Guide

Doors

Guide

Bottom Track

Self-Tapping

Screws

8-32 x 1/4"

Bottom Track

Insert the bushings and handle bases into the

door panel holes. Thread the knobs onto the

handle bases. On the outside panel, the knob

installs on the outside of the shower. On the

inside panel, the knob installs on the inside of

the shower.

Outside Panel Inside Panel

Bushings

Showerhead

Handle Hole

Label

On the inside panel, assemble a roller to the

middle hole of each hanger bracket. Install the

rollers on the side of the door panel that is

opposite the label.

Label Side

Roller

Screw

Label

#8-32 x 3/8"

Before proceeding, identify which door panel will

install on the inside track. The inside panel will be

the door panel closest to the showerhead. When

the inside panel is in position, the label will be on

the outside of the shower and the handle hole will

be next to the wall jamb.

Label

Side

Screw

#8-32 x 3/8"

Label

Rollers

On the outside panel, assemble a roller to the

middle hole of each hanger bracket. Install the

rollers on the same side of the door panel as the

label.

Handle

Hole

Lift the inside panel onto the inside track. The

label faces the outside of the shower.

Handle Hole

Handle Base

Knob

Handle

Base