Installation Instructions
1
5407 Series Bypass Shower and Bath Doors
Installation Guide
Slide the notched end of the insert into the groove
and pull the notch to the end of the bottom track.
Trim the insert to be flush with the bottom track.
Position the bottom track on the center of the
ledge. If needed, file the ends to match the
corners.
Position the wall jambs over the bottom track.
Plumb both wall jambs. Mark the screw holes.
Remove the wall jambs. Drill 5/16” holes into the
walls and insert the anchors.
*Call Customer Care Center to order replacement parts.
**Finish/color code must be specified when ordering.
Retain this document for future servicing.
Record model number from box for reference.
CAUTION: Risk of injury. Do not attempt to cut
tempered glass.
IMPORTANT! Do not cut the top track the same
length as the bottom track.
Walls must be within 3/8" (10 mm) of plumb.
Cover drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's
instructions for application and curing time.
Installation video available at
SterlingPlumbing.com.
Parts Identification
7
8
2
3
Bypass Shower DoorsBypass Bath Doors
Required Tools
6
Model Number:______________
1183935-2-A
Measure distance "A." Subtract 1/4" (6 mm) or
the width of a number 2 pencil from "A" and cut
the bottom track.
Apply silicone sealant in the groove on the
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
100% Silicone Sealant Masking Tape
32 Teeth Per Inch Blade
Miter Box
Number 2 Pencil 3/16"
5/16" Masonry Bit for Tile
5/16"
1058298**
Hardware Skin Pack
Insert
1/4" (6 mm)
Cut Line
"A" Mark
Leg
Notch
1
2
3
Screw Cover
Screw Cover
#8-18 x 1-1/2"
A
A
Groove
Bottom Track
Tin Snips
USA: 1-800-STERLING (1-800-783-7546)
Mexico: 001-877-680-1310
SterlingPlumbing.com
Right Door
Panel*
Handle (2 ea.)
1172515**
#8-32 x 3/8"
8-32 x 1/4"
Screw
Bottom Wall
Jamb Notch
Bottom Track
1058626-02**
#8-18 x 1-1/2"
1048208-C
Center Guide
1058294**
Screw
1056868-A
Wall Jamb*
Insert
1053530
Bottom Wall
Jamb Notch
Bushing (4 ea.)
1184243
Screw
1051142-A
Roller
1044585
Hanger Bracket
1077761-01**
Blind Nut
1050048-B
Bushing
1059792
Top Track
1058827-05**
Screw Cover
1031943**
Bumper
1081001
Anchor
1077762
Sex Bolt
1077763-A
Series Number Label
Wall Jamb*
Left Door
Panel*
Top Track
B
B
"B" Mark
Cut Line
1/32" (1 mm)
x2
x2
x2
4
1
Center the bottom track on the ledge with the leg
to the outside. Tape the bottom track in place and
mark the position.
Reposition both wall jambs. Secure the wall jambs
with screws. Attach a bumper at the top and
bottom locations.
9
Important! The bottom track and wall jamb must
sit flat against the shower ledge and the wall. If
needed, trim and file the wall jamb. Use a coin to
match and to transfer the corner radius of the
shower to the wall jamb.
5
10
Measure distance “B” above the wall jambs.
Subtract 1/32" (1 mm) or the width of a saw
blade from “B.” Mark and cut the top track.