OWNER'S MANUAL FAN HEATER INS-SOA_1222 SOA (A)SOA2002WCW (A)SOA2002W (A)SOA1501PW THANK YOU FOR YOUR PURCHASE! QUESTION? PROBLEM? CONTACT STELPRO CUSTOMER SERVICE. WWW.STELPRO.COM CONTACT@STELPRO.
IMPORTANT INSTRUCTIONS Before installing and using this product, you must read and understand these instructions and keep them for future reference. If the installer and the user do not follow these instructions, the manufacturer cannot be held liable in any way and the warranty will be null and void.
INSTALLING THE FAN HEATER TO ENSURE A SAFE AND EASY INSTALLATION, TAKE A FEW MINUTES TO READ THIS INSTALLATION GUIDE. WHAT IS IN THE BOX TOOLS REQUIRED Level Flat screwdriver OASIS Fan heater (A)SOA1501PW MODEL Stud finder Tape measure 4 to 6 No. 6 to No. 10 round-head wood screws and suitable brackets to secure the fan heater (4.3 kg or 9.
WARNING: This product must be installed by a certified electrician according to the electrical and building codes effective in your region. 1 WHERE TO INSTALL YOUR OASIS FAN HEATER Install your fan heater in an unobstructed location at least 6 in. (15 cm) off the ground. WARNING: To avoid any risk of overheating, leave a clearance of at least 12 in. (30 cm) in front of the fan heater and 6 in. (15 cm) on either side of it.
3 PREPARING THE SURFACE FOR INSTALLATION 1. Locate the studs and any other structures that might be inside the wall. FOR A RECESSED INSTALLATION FOR A WALL MOUNT INSTALLATION 2. For a recessed installation, make an opening as shown in the diagram. For a more secure installation, attach one side of the unit to a stud. 10 1/4 in. (26 cm) NOTE: Avoid using an exterior wall for recessed installations as this decreases the wall's insulation. 14 in. (36 cm) 3.
5 INSTALLING THE FAN HEATER FOR A RECESSED FAN HEATER INSTALLATION FOR A WALL MOUNT FAN HEATER INSTALLATION 1. Insert the fan heater into the hole made in the wall and mark the position of the screws according to the mounting holes [F]. Make sure the fan heater is level. 1. Place the fan heater against the wall and mark the position of the screws according to the mounting holes [G] at the back of the unit. Make sure the fan heater is level. 2.
4. Then place all the wires in the junction box. Replace the junction box cover [F] and insert the screw [G] to hold it in place. NOTE: If this unit will be controlled by a wall-mounted thermostat (without an integrated thermostat), use the switch [H] above the motor to select the desired power. The required power depends on the size of the room to be heated and represents approximately 1.25 W per cubic foot (0.03 per m3). The power requirement may vary depending on a number of factors.
INSTALL THE SOA1501PW MODEL (WITH A POWER CORD) 1 UNHOOK THE WALL BRACKET FROM THE DEVICE 3 1. Using a screwdriver, press the plastic tab [A] under the device. 2. Hold the tab down and rotate the bracket slightly. 3. Pull out the bracket to remove the upper hooks from the device. 2 A 1 2 3 INSTALL THE WALL BRACKET 1. Position the wall bracket at the desired height respecting the clearances from the floor. Make sure the unit is close enough to an electrical outlet. HANG AND PLUG IN THE DEVICE 1.
USING THE FAN HEATER WITH BUILT-IN THERMOSTAT WARNING: Before using your fan heater, make sure that it has been installed by a certified electrician in accordance with the electrical and building codes in your area. Do not operate without front panel. The following sections outline how to control the fan heater with its built-in electronic thermostat. (SOA...
USING BOOST MODE BOOST mode allows you to increase room temperature quickly for a given period of time. When you use BOOST mode, the fan heater operates at a higher speed and power to increase room temperature quickly. When the desired temperature is reached, the power decreases, but the fan heater maintains the BOOST mode setpoint temperature. To activate BOOST mode: By default, BOOST mode is set to 30 °C (86 °F). To learn how to change it, see Defining the setpoint temperature for BOOST mode.
Selecting the temperature display unit (°C or °F) By default, the temperature displays in degrees Celsius for SOA models and in degrees Fahrenheit for ASOA models. To change the temperature display unit: 1. Access menu 1. 2. Select °C or °F. 3. Confirm the selection. Activating or deactivating open window detection The thermostat can detect if a window is open in the room where the fan heater is located.
TROUBLESHOOTING THE FAN HEATER The following table outlines the most common issues and alerts you could experience with your fan heater. If your problem is not listed in the table below or the proposed solution does not solve the problem, turn the power off and contact our customer service team. WWW.STELPRO.COM CONTACT@STELPRO.COM 1-844-STELPRO PROBLEM/ALERT POSSIBLE CAUSE AND SOLUTION The fan heater is not operational after installation.
RESTARTING THE FAN HEATER AFTER THE THERMAL PROTECTION IS TRIGGERED With a built-in thermostat In the event of overheating, the unit’s thermal protection will trigger to prevent damage. When this happens, heating is switched off, but ventilation continues to evacuate heat, which is considered ventilation without heat. Once the thermal protection is triggered, you must restart the fan heater to resume normal operation: NOTE: If the fan heater has a built-in thermostat, the will appear on the display.
TECHNICAL INFORMATION Built-in control device Thermistor used as a sensor that does not carry a charge Software Class A Nature of supply Device for alternating current only Type of controlled load Resistive Action Type 1.
