assembly Instructions

ManualsBrandsSteinel ManualsElectrical & LightingSensor LED spotlight XLED Home 2 Z-Wave

Advanced Conﬁguration

For more detailed information, please download the profes-

sional instructions from z-wave�steinel�de.

A� Description of device endpoints:

The functionality of the device is divided to endpoints by

their using.

0 = ROOT

To root summarizes whole device function, to root endpoint is

mapped all functionality from the endpoint 1 and most of the

endpoints 2 and 3.

Device type = On/O Power Switch

Supported Command Classes:

COMMAND_CLASS_ZWAVEPLUS_INFO ( v2 )

COMMAND_CLASS_BASIC ( v1 )

COMMAND_CLASS_VERSION ( v2 )

COMMAND_CLASS_FIRMWARE_UPDATE_MD ( v3 )

COMMAND_CLASS_MANUFACTURER_SPECIFIC ( v2 )

COMMAND_CLASS_MULTI_CHANNEL ( v4 )

COMMAND_CLASS_DEVICE_RESET_LOCALLY ( v1 )

COMMAND_CLASS_CONFIGURATION ( v1 )

COMMAND_CLASS_POWERLEVEL ( v1 )

COMMAND_CLASS_NODE_NAMING ( v1 )

COMMAND_CLASS_NOTIFICATION ( v4 )

COMMAND_CLASS_ASSOCIATION ( v2 )

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION ( v3 )

COMMAND_CLASS_ASSOCIATION_GRP_INFO ( v1 )

COMMAND_CLASS_SWITCH_BINARY ( v1 )

COMMAND_CLASS_SCENE_ACTIVATION ( v1 )

COMMAND_CLASS_SCENE_ACTUATOR_CONF ( v1 )

COMMAND_CLASS_SWITCH_ALL ( v1 )

COMMAND_CLASS_APPLICATION_STATUS ( v1 )

COMMAND_CLASS_SENSOR_MULTILEVEL ( v4 )

Controlled Command Classes:

COMMAND_CLASS_BASIC ( v1 )

1 = LAMP

To endpoint 1 is mapped basic lamp functionality.

Device type = On/O Power Switch

Supported Command Classes:

COMMAND_CLASS_ZWAVEPLUS_INFO ( v2 )

COMMAND_CLASS_BASIC ( v1 )

COMMAND_CLASS_ASSOCIATION ( v2 )

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION ( v3 )

COMMAND_CLASS_ASSOCIATION_GRP_INFO ( v1 )

COMMAND_CLASS_SWITCH_BINARY ( v1 )

COMMAND_CLASS_SCENE_ACTIVATION ( v1 )

COMMAND_CLASS_SCENE_ACTUATOR_CONF ( v1 )

COMMAND_CLASS_SWITCH_ALL ( v1 )

COMMAND_CLASS_APPLICATION_STATUS ( v1 )

Controlled Command Classes:

2 = MOTION SENSOR

To endpoint 2 is mapped motion sensor (PIR) functionality.

Device type = Sensor - Notiﬁcation

Supported Command Classes:

COMMAND_CL ASS _Z WAVEPLUS_INFO ( v2 )

COMMAND_CL ASS _BASIC ( v1 )

COMMAND_CLASS_ASSOCIATION ( v2 )

COMMAND_CL ASS _NOTIFICATION ( v4 )

COMMAND_CLASS_MULTI_CHANNEL_ ASSOCIATION ( v3 )

COMMAND_CLASS_ASSOCIATION_GRP_INFO ( v1 )

Controlled Command Classes:

COMMAND_CL ASS _BASIC ( v1 )

Special meaning of BASIC CC:

BASIC CC can activate/temporary deactivate internal motion

sensor using for evaluating the behaviour of the lamp and

groups 2 and 3. Events are, however, still transmitted to the

Lifeline, and the device can be controlled via remote motion

sensors (please also follow the conﬁguration parameter 16).

Basic Set: active ( 0xFF ) / inactive ( 0x00 ) sensor function

Basic Get: get sensor activity

Basic Report: sensor activity status

3 = AMBIENT LIGHT SENSOR

To endpoint 3 is mapped ambient light sensor ( lumines-

cence sensor synchronized with lamp ) functionality.

Device type = Sensor - Multilevel

Supported Command Classes:

COMMAND_CLASS_ ZWAVEPLUS_INFO ( v2 )

COMMAND_CLASS_ SENSOR_ MULTILEV EL ( v4 )

COMMAND_CLASS_ASSOCIATION ( v2 )

COMMAND_CLASS_MULTI_CHANNEL_ ASSOCIATION ( v3 )

COMMAND_CLASS_ASSOCIATION_GRP_INFO ( v1 )

Controlled Command Classes:

B� Description of association groups:

0 = ROOT DEVICE

Group 1 – "Lifeline" – only 1 node

Lifeline messages

- Device Reset Locally

- Notiﬁcations:

0x09 ( System ) – Hardware failure with manufacturer

proprietar y code ( 0x03 )

0x09 ( System ) – Software failure with manufacturer

proprietary code ( 0x04 )

0x07 ( Home security ) – Motion Begin event ( 0x08 )

0x07 ( Home security ) – Motion End event ( 0x00, 0x08 )

- Binary Switch Report – lamp state

- Multilevel Sensor Report – value of internal ambient light

sensor

Motion Begin and Motion End events are sent along with

frames to group 3. If multichannel association is created the

events are sent from motion sensor endpoint.

Switch Report is sent immediately upon a change of status

along with frames to group 2. If multichannel association is

created the events are sent from lamp endpoint.

Multilevel Sensor Report is sent a maximum of once per

1minute (if the value has changed by least by 3%) and

a minimum of once per 15 minutes (if the value has not

changed). If the ambient light value is old (cannot measure

because of permanent light), the value is not transmitted via

lifeline. Multilevel Sensor Report can be also added to some

other events to send in bulk. If multichannel association is

created the events are sent from light sensor endpoint.

All notiﬁcations to lifeline are sent as sensor states regard-

less of sensor settings and states as SLAVE_MODE,

LOCAL_DISABLED and MOTION_ENABLE.

Group 2 – "On/O control" – max 16 nodes

Group 2 is used for directly controlling Z-Wave devices via

BASIC SET commands through the evaluation of movement

and light as with internal use ( so that all of these devices work

together ). This is intended for use especially with third-party

devices that do not implement reactions for motion events.

BASIC_SET and similar Z-Wave commands are not retrans-

mitted intentionally to slaves and must be sent to slave devic-

es via the controlling device simultaneously. Only for use in

master-slave system, multidevice control is not possible.

– 32 –

– 33 –

Guasto Causa Rimedio

Il faro LED a sensore è senza

tensione

Fusibile difettoso, lampada

non accesa, punto di interru-

zione nel cavo

Corto circuito

Sostituite il fusibile, accendete

l'interruttore, controllate la linea di

alimentazione con un voltmetro

Controllate gli allacciamenti

Il faro LED a sensore non si

accende

Nel funzionamento con luce

diurna l'impostazione crepu-

scolare è regolata sul funzio-

namento di notte

Interruttore di rete su OFF

Fusibile difettoso

Campo di rilevamento non

impostato in modo mirato

Eseguite una nuova impostazione

Accendete

Cambiate fusibile, eventualmente

controllate l'allacciamento

Eseguite una nuova regolazione

Il faro LED a sensore non si

spegne

Movimento continuo nel

campo di rilevamento

Controllate il campo di rilevamen-

to, eseguite eventualmente una

nuova regolazione o una scher-

matura

Il faro LED a sensore si accende

e spegne in continuazione

Animali in movimento nel

campo di rilevamento

Orientate il sensore più in alto o

copritelo in modo mirato, spostate

o coprite il campo di rilevamento

Il faro LED a sensore interviene a

sproposito

Vento che muove alberi e

cespugli all'interno del campo

di rilevamento

Vengono rilevate automobili

sulla strada

Improvvisi sbalzi di temperatu-

ra dovuti a condizioni atmosfe-

riche (vento, pioggia, neve) o

causati da aria di scarico di

ventilatori o da aria provenien-

te da ﬁnestre aperte

Il faro LED a sensore oscilla

(si muove) per es. in seguito a

rache di vento o a forti

precipitazioni

Spostate il campo

Modiﬁcate il campo o spostate il

luogo di montaggio

Montate il faro LED a sensore su

una base stabile

Non è possibile aggiungere

l'apparecchio (l'apparecchio non

è stato ancora aggiunto)

Distanza eccessiva tra

controller Z-Wave e

apparecchio

Riducete la distanza dal controller

Z-Wave

Montate un ripetitore Z-Wave

Non è possibile aggiungere

l'apparecchio

È già stato aggiunto Rimuovete l'apparecchio dalla

rete esistente

Eseguite il default reset

Il LED di stato

lampeggia

ogni 5 secondi per 1 secondo

Nessun contatto radio con la

Smart Friends Box o altri

controller Z-Wave

Riavviate la Smart Friends Box o

il controller Z-Wave

Riducete la distanza dal controller

Z-Wave

Montaggio di un ripetitore

Z-Wave

Il LED di stato

lampeggia

rapidamente e permanentemen-

Errore critico Staccate per breve tempo

l'apparecchio dalla tensione di

rete

12� Disturbi di funzionamento