assembly Instructions

- 10 - - 11 -
Note: weather conditions may affect the way the
sensor works. Strong gusts of wind, snow, rain or
hail may cause the light to come on when it is not
wanted.
4. Installation
To achieve the stated reach of 5m, the light should
be mounted at a height of approx. 2m.
Connecting the mains supply lead
(see illustration)
The supply lead consist of three wires:
= Phase conductor (usually black, brown or grey)
= Neutral conductor (usually blue)
= Protective-earth conductor (green/yellow)
If you are in any doubt, identify the conductors using
a voltage tester; then disconnect from the power
supply again. Phase and neutral conductor
are connected to the terminal block.
Important: incorrectly wired connections will
produce a short circuit later on in the product or
your fuse box. In this case, you must identify the
individual conductors once again and reconnect
them. A mains switch for switching the light ON and
OFF can of course be fitted in the mains lead.
Note: to connect the light, the light enclosure
must be fitted on the mounting hooks to prevent
the internal wiring from being exposed to strain.
5. Functions
The sensor-switched light can be put into service
after mounting the enclosure and connecting to
the mains power supply. The light will also work
without being integrated into a Z-Wave network.
In this case, the time setting is permanently set
to 3minutes. When putting the light into opera-
tion, the light will switch OFF after the 10-second
calibration phase and is then activated for sensor
mode. This light can now be integrated into the
Z-Wave network.
After the initialisation phase, the red LED signalises
inclusion in / exclusion from the Z-Wave network.
The LED is ON for 1 second (the light is included)
or 10seconds (the light is excluded).
The settings can be made via the control dials or
via Z-Wave network. The settings last selected will
always be in effect regardless of whether they were
made via the control dials or via Z-Wave network.
Reach setting (sensitivity)
Factory setting: 5m
Reach can be infinitely varied from 1m to 5m
Adjustment control set to:
+ = maximum reach 5m
– = minimum reach 1m
Reach is the term used to describe the radius of
the detection zone produced on the ground when
mounting the light at a height of 2 m.
Twilight setting (response threshold)
Factory setting: 2000 lux
The chosen response threshold can be infinitely
varied from approx. 2–2000 lux.
Adjustment control set to:
= daylight operation
approx. 2000lux.
= night-time operation
approx. 2lux.
To adjust the detection zone in daylight, the control
dial must be set to .
Programme setting
0 = no basic light level ON from
twilight setting selected
10 = basic light level 10 minutes
30 = basic light level 30 minutes
= basic light level all night long
What is basic light level?
The basic light level provides continuous night-
time illumination at approx. 10% light output. The
light only switches to maximum output (100%) for
the time selected in response to movement in the
detection zone. The light then returns to the basic
light level (approx. 10%).
Note: depending on the local power grid, the LEDs
may flicker slightly when dimmed. This is not a
product defect and no reason for complaint.
What is soft light start?
The sensor-switched light features a soft light start
function. This means that when turned ON, the
light is not switched directly to maximum output
but gradually builds up brightness to 100% within
the space of a second. Brightness is also gradually
reduced when the light is switched OFF.
1 m – 5 m
2 – 2000 lux
6. Integration into Z-Wave networks
This product can be operated in any Z-Wave net-
work with other Z-Wave certified devices from other
manufacturers. All non-battery operated nodes
within the network will act as repeaters regardless
of vendor to increase reliability of the network.
Inclusion Add
Exclusion Remove
These instructions for including and excluding
Steinel Z-Wave products have been written for the
Smart Friends system. They may not always apply
to other Z-Wave products. You will find further
details in the description of your Z-Wave controller.
(To start the light's inclusion or exclusion mode,
briefly press button
).
Following exclusion, all configuration parameters
(time, sensitivity etc.) remain intact until next inclu-
sion and the light now works in standalone mode –
as a result, Z-Wave can also be used for the light’s
standalone setting.
Z-Wave button
Button for inclusion and exclusion
as well as for returning the device
to the factory setting.
Adding L810LEDiHF to the Smart Friends
system:
1 Download Smart Friends app from the
AppStore.
2 In the rooms view, activate the edit mode.
3 Select the chosen room and press the "Add
device" button.
4 Briefly press the device's button
to set the
light to inclusion mode. The status LED
lights
up to show that this mode is selected.
The red LED flashes slowly during the exclusion
process. After this process the red LED is ON
for 10 seconds (the light is still excluded from
the Z-Wave network) or for 1 second (the light
is included).
5 The app displays a confirmation message once
inclusion has been successfully completed.
Removing L810LEDiHF from the Smart
Friends system:
1 In the rooms view, activate the edit mode.
2. Select the device in the chosen room and press
the "delete"
button. Press delete and follow
the instructions in the app.
3 Briefly press the device's button to set the
light to exclusion mode. The red status LED
lights up to show that this mode is selected.
The red LED flashes slowly during the exclusion
process. After this process the red LED is ON
for 10 seconds (the light is still excluded from
the Z-Wave network) or for 1 second (the light
is included).
4 The app displays a confirmation message once
exclusion has been successfully completed.
Setting L810LEDiHF with the app
– After programming, an ON/OFF scene is auto-
matically created in the app.
– The following setting values are then automatical-
ly stored:
a) Twilight setting = control-dial setting
b) Z Time setting = 3 min switch-o delay
– The twilight and time settings can be selected to
the accuracy of one lux and one second respec-
tively in the "Scene" menu.
Returning L 810 LED iHF to factory settings:
Please only perform these steps if the main net-
work controller is missing or not working for other
reasons.
1 Briefly press button
and directly afterwards
keep it pressed for 5 seconds.
2 Status LED
briefly flashes to show that the
light has been reset.
3 The device is now no longer included in the
Z-Wave system and has been returned to
factory settings.
Firmware updating:
After sending new firmware for the internal micro-
processor (target 1), the light is reset and the new
firmware is programmed in. During this process,
the red and blue LEDs flash separately.
GB