assembly Instructions

- 18 - - 19 -
segments to limit reach as required.
Inadvertent triggering is ruled out or
the sensor can be targeted to watch
over danger spots. (Fig�5�4)
7� Integration into Z-Wave
networks
This product can be operated in any
Z-Wave network with other Z-Wave
certified devices from other manu-
facturers. All non-battery operated
nodes within the network will act as
repeaters regardless of vendor to
increase reliability of the network.
Inclusion Add
Exclusion Remove
These instructions for including and
excluding STEINEL Z-Wave products
have been written for the Smart
Friends system. They may not always
apply to other Z-Wave products. You
will find further details in the descrip-
tion of your Z-Wave controller. (To
start the motion detector's inclusion
or exclusion mode, turn the device's
control dial
to "Set" and back to
"0" within 5seconds).
Following exclusion, all configuration
parameters (time, sensitivity etc.)
remain intact until next inclusion and
the light now works in standalone
mode – as a result, Z-Wave can also
be used for the light’s standalone
setting.
6� Function
The motion detector will also work
without being integrated into a
Z-Wave network. In this case, the
time setting is permanently set to
3minutes. When putting the motion
detector into operation, it will switch
OFF after the 10-second calibration
phase and is then activated for sen-
sor mode. The motion detector can
now be integrated into the Z-Wave
network.
The settings can be made via the
control dials or via Z-Wave network.
The settings last selected will always
be in eect regardless of whether
they were made via the control dials
or via Z-Wave network.
Factory settings
Twilight level
: 2000lux
Time setting: 3 min
Twilight setting (Fig�5�1/C)
can be infinitely varied
Control dial set to
=
twilight operation, approx. 2 lux
Control dial set to
=
daylight operation, approx. 2000 lux
Note: To adjust the detection zone in
daylight, the control dial must be set
to
= daylight operation.
Reach setting/adjustment
The detection zone can be optimised
to suit requirements.
Sensor unit
– Sensor unit swivels through 180°.
(Fig�5�2)
– Sensor unit tilts through 90°.
(Fig�5�5)
Adhesive shrouds (Fig�5�3)
The film shroud can be used for
masking out any number of lens
3 To put the device into exclusion
mode, turn the device's control dial
to "Set" and back to "0" within
5seconds. The red status LED
lights up to show that this mode is
selected.
4 The app displays a confirmation
message once exclusion has been
successfully completed.
Setting IS 140-2 with the app
– After programming, an ON/OFF
scene is automatically created in
the app.
– The following setting values are
then automatically stored:
a) Twilight setting = control-dial
setting
b) Time setting = 3 min switch-
OFF delay
– The twilight and time settings can
be selected to the accuracy of a
lux / second in the "Scene" menu.
Resetting the IS 140-2 to factory
settings:
Please only perform these steps if the
main network controller is missing or
not working for other reasons.
1 Turn the device's control dial
to
"Set" and move it to "Reset" within
5 seconds.
2 Status LED
briefly flashes to
show that the light has been reset.
3 The device is now no longer includ-
ed in the Z-Wave system and has
been reset to factory settings.
Note: the current firmware version for
the light is available for downloading
from z-wave�steinel�de.
Z-Wave control dial (E)
Control dial for
inclusion and
exclusion as well as
for returning the
device to the factory
setting.
Adding IS 140-2 to the
Smart Friends system:
1 Download Smart Friends app from
the app store.
2 In the rooms view, activate the
edit mode.
3 Select the chosen room and press
the "Add device" button.
4 To put the device into inclusion
mode, turn the device's control dial
to "Set" and back to "0" within
5seconds. Status LED
lights up
to show that this mode is selected.
5 The app displays a confirmation
message once inclusion has been
successfully completed.
Removing IS 140-2 from the
Smart Friends system:
1 In the rooms view, activate the
edit mode.
2 Select the device in the chosen
room and press the "delete"
button. Press delete and follow the
instructions in the app.