User Manual

- 18 - - 19 -
Other functions of GluePRO400LCD
Other functions of GluePRO400LCD
LOC function
To avoid altering the chosen settings unin-
tentionally, the GluePRO400LCD comes
with the Lockable Override Control function
(LOC). To find out how to set the LOC
function, contact our Service Department
on +44/1733/366-700.
Idle mode
After any selectable period, idle mode au-
tomatically reduces the temperature in the
heating element to a temperature you can
select. This depends on when the button
was last pressed. Idle state is indicated by
the blue flashing LED / blue flashing dis-
play. On leaving the factory, this function
is deactivated. To find out how to set idle
mode, contact our Service Department on
+44/1733/366-700.
1. Hold the tool with heat-protective
gloves.
2. Unscrew nozzle
13
.
At this point, never pull the
trigger!
3. Screw the replacement nozzle on
hand-tight.
Operation/Function
Getting started
L Plug the tool in.
L Switch the tool ON by pressing the
ON/OFF button for two seconds.
The tool immediately heats up to the
selected temperature.
L While it is heating up, the LED flashes
red / the display lights up blue.
L Once the LED shows red / the display
lights up green, the temperature set-
ting range has been reached and the
hot-melt glue applicator is ready for
use.
L If the temperature range is too high,
the LED / display lights up red.
L Insert the hot-melt glue stick into the
opening at the rear of the tool.
L Switch the tool OFF by briefly pressing
the ON/OFF button.
Temperature setting
GluePRO400 LCD
L The temperature can be selected to
an accuracy of one degree from 40 to
230 degrees Celsius. On leaving the
factory, the tool is set to 190 degrees
Celsius.
L Press the SET button
6
. Keeping
the SET button pressed, select the
chosen temperature via the
7
+
8
UP and DOWN buttons. The tem-
perature you select is shown on the
display.
L Releasing the
6
SET button shows
you the temperature now reached in
the heating chamber.
L Keep the SET button pressed. Pressing
the UP or DOWN button automatically
increases or reduces temperature in
steps of 1 degree. Keeping the UP or
DOWN button pressed for at least
3seconds increases or reduces tem-
perature by 5degrees.
L
Do not select any temperature
higher than is needed for apply-
ing the hot-melt adhesive!
Stroke adjustment
L Glue feed can be adjusted to suit any
particular application, giving you pre-
cision in selecting an exact quantity of
glue per stroke and letting you set the
feed trigger
12
for ease of use.
L The slide control for adjusting glue
feed
3
adjusts the trigger
12
to re-
duce or increase the quantity of glue
delivered.
L Pull the trigger and move the glue feed
slide control
3
towards the nozzle
until the tool delivers the chosen
quantity of glue per trigger pull or
gives you the delivery rate you find
easy to work with.
L Adjust the slide control in the opposite
direction to restore the initial position.
Changing nozzles
Customised nozzles are available for spe-
cific applications. To change the nozzle,
the tool must be warm and unplugged.
For this, heat up the GluePRO300 for no
more than 45seconds
Heat the GluePRO400 LCD to no more
than 100 degrees Celsius.
Switch the tool OFF once it has reached
temperature.
Technical specifications
GluePRO300 GluePRO400 LCD
Warm-up time < 3min to 190°C < 2 min to 190°C
Melt temperature 190°C 40°C - 230°C
Maximum delivery rate* 1.2 kg/h 1.5kg/h
Dimensions 290 × 230 × 70 mm 290 × 230 × 70 mm
Supply voltage 220 - 230 V / 50/60 Hz 220 - 230 V / 50/60 Hz
Output (idle phase) 30 W 40 W
Maximum power consumption 300 W 400 W
Rated input power** 90 W 110 W
Weight Approx. 580 g Approx. 600 g
Glue sticks Genuine STEINEL 11 mm glue sticks
*Depending on temperature and glue viscosity
**For 30 s of gluing / 60 s pause
GB