4.0
Table Of Contents
- Audio effects
- The included effect plug-ins
- Introduction
- Delay plug-ins
- MonoDelay
- PingPongDelay
- Dynamics plug-ins
- Gate
- Limiter
- VSTDynamics
- Filter plug-ins
- WahWah
- Modulation plug-ins
- Flanger
- Phaser
- Rotary
- Tremolo
- Vibrato
- Other plug-ins
- Octaver
- Tuner
- Spatial plug-ins
- MonoToStereo
- StereoEnhancer
- Earlier VST plug-ins
- Distortion plug-ins
- DaTube
- Dynamics plug-ins
- MIDI Gate
- Filter plug-ins
- StepFilter
- Modulation plug-ins
- Metalizer
- Ringmodulator
- Tranceformer
- Other plug-ins
- Bitcrusher
- Chopper
- Restoration plug-ins
- Grungelizer
- Reverb plug-ins
- RoomWorks SE
- VST Instruments
- HALionOne
- Index
24
The included effect plug-ins
Rotary
The Rotary plug-in simulates the classic effect of a rotary
speaker. A rotary speaker cabinet features variable speed
rotating speakers to produce a swirling chorus effect,
commonly used with organs. Rotary features all the pa-
rameters associated with the real thing.
The parameters are as follows:
Directing MIDI to the Rotary
For real-time MIDI control of the Speed parameter, MIDI
must be directed to the Rotary.
• Whenever the Rotary has been added as an insert ef-
fect (for an audio track or an FX channel), it will be avail-
able on the Output Routing pop-up menu for MIDI tracks.
If Rotary is selected on the “out:” menu, MIDI will be directed to the plug-
in from the selected track.
Tremolo
Tremolo produces amplitude (volume) modulation.
Parameters are as follows:
Parameter Description
Speed
(Stop/Slow/Fast
This controls the speed of the Rotary in three steps.
Mode Selects whether the Slow/Fast setting is a switch or a
variable control. When switch mode is selected and Pitch
Bend is the controller, the speed will switch with an up or
down flick of the bender. Other controllers switch at 64.
Speed Mod Selects the Rotary speed from 0 (Stop) to 100 (Fast).
Overdrive Applies a soft overdrive or distortion.
Crossover Freq. Sets the crossover frequency (200–3000Hz) between
the low and high frequency loudspeakers.
Slow Fine adjustment of the high rotor Slow speed.
Accel. Fine adjustment of the high rotor acceleration time.
Fast Fine adjustment of the high rotor Fast speed.
Amp Mod High rotor amplitude modulation.
Freq Mod High rotor frequency modulation.
Slow Fine adjustment of the low rotor Slow speed.
Fast Fine adjustment of the low rotor Fast speed.
Accel Fine adjustment of the low rotor acceleration time.
Amp Mod. Adjusts amplitude modulation depth.
Level Adjusts overall bass level.
Phase Adjusts the amount of phasing in the sound of the high
rotor.
Angle Sets the simulated microphone angle. 0 = mono, 180 =
one mic on each side.
Distance Sets the simulated microphone distance from the
speaker in inches.
Output Adjusts the overall output level.
Mix Adjusts the mix between dry and processed signals.
Parameter Description
Tempo sync on/
off
The button below the Rate knob is used to switch tempo
sync on or off. The button is lit when tempo sync is on.
Rate If tempo sync is on, this is where you specify the base
note value for tempo-syncing the effect (1/1 to 1/32,
straight, triplet or dotted).
If tempo sync is off, the modulation speed can be set
freely with the Rate knob, without sync to tempo.
Depth This governs the depth of the amplitude modulation.
Spatial This will add a stereo effect to the modulation.
Output Adjusts the output volume.