Plug-in Reference

91
The included VST instruments
Envelope
In the Envelope section, the following parameters are
available:
LFO
In the LFO section, the following parameters are available:
X/Y Pad
In the X/Y Pad section, the following parameters are avail-
able:
Effects
In the Effects section, the following parameters are avail-
able:
Key Track Determines the amount of key tracking applied to the filter
cutoff frequency. The available range is 0 to 100
%. A
range of 100
% tunes the filter cutoff frequency to the
keyboards pitch 1:1.
Mod Src
(A+B)
Defines the filter modulation source. The available
sources are: Modwheel, Aftertouch, Pitchbend, Velocity,
LFO, and Mod Env.
Depth
(A+B)
Controls the filter modulation depth for the mod source
set in the “mod src” field.
Parameter Description
A – (Attack) Sets the attack time.
D – (Decay) Sets the decay time.
S – (Sustain) Sets the sustain level.
R – (Release) Sets the release time.
Mod Src
(A+B)
Defines the envelope modulation source. You can select:
Modwheel, Aftertouch, Pitchbend, Velocity, LFO and
Mod Env.
Depth (A+B) Controls the envelope modulation depth for the mod
source defined in the “mod src” field.
Parameter Description
Waveform
(pop-up menu)
Here, you can select the waveform for the low frequency
oscillator. Available waveforms are: Triangle, Square,
Sawtooth, Sample & Hold and Random.
Rate Adjusts the frequency of the LFO, thus changing the rate
of the modulation. Depending on the LFO sync parame
-
ter, you can edit the rate in Hertz or in note values.
Sync When “Sync” is “on” the LFO speed is synchronized to
the sequencer’s tempo. This also affects the LFO rate
format.
Mod Src Defines the LFO modulation source. Available sources
are:
Modwheel, Aftertouch, Pitchbend, Velocity, LFO and
Mod Env.
Depth Controls the LFO modulation depth for the mod source
defined in the “mod src” field.
Parameter Description
Parameter Description
X Par Sets the parameter to be modulated on the x axis of the
XY Pad. All of Monologue’s parameters are available as
destinations.
Y Par Sets the parameter to be modulated on the y axis of the
XY Pad.
XY Pad Use the mouse to control any two of Monologue’s param-
eters in combination. By moving the mouse horizontally,
you can control the x parameter, by moving it vertically,
you can control the y parameter. You can also record
controller movements as automation data.
Parameter Description
FX Type
(pop-up menu)
Selects the effect type for Monologue’s pitch effects. The
available types are Chorus, Flanger and Phaser.
Rate Use this to adjust the rate of the effect modulation.
Depth Use this to adjust the depth of the effect modulation.
FBK Controls the feedback of the effect.
Mix Controls the balance between dry and wet (effect) signal.
Set to 0, the effect is off. Set to 50, the balance between
dry and wet signal is 50/50.
Overdrive Controls the amount of overdrive (distortion) added to the
signal. A
slight amount of overdrive creates punch and
bottom. Higher amounts add distortion.
Delay Sets the delay time in musical values. The delay effect is
always in sync with the song tempo.
Spread Controls the stereo spread of the delay signal. If you set
this to 0, the delay is centered mono. Higher amounts of
spread shift the left and right delay channels. If you set
this to 100, the delays “ping-pong” between the left and
right channels at an even rate.
Tone Adds a low pass filter to the delay. Increasing “tone”
makes every delay repetition darker in tone.
FBK Controls the amount of feedback of the delay. High feed-
back levels create infinite delays. Use this parameter with
caution.
Mix Controls the balance between dry and wet (effect) signal.
Set to 0, the effect is off. Set to 50, the balance between
dry and wet signal is 50/50.