Plug-in Reference

25
The included effect plug-ins
The following parameters are available:
Filter plug-ins
This section contains descriptions of the plug-ins in the
“Filter” category.
DualFilter
The DualFilter effect filters out certain frequencies while
allowing others to pass through.
The following parameters are available:
Parameter Description
Band 1 Gain
(-20 to +24 dB)
Sets the amount of cut/boost for the low band.
Band 1 Inv button Inverts the gain value of the filter. Use this button to fil-
ter out unwanted noise. While looking for the fre-
quency to omit, it sometimes helps to boost it in the
first place (set the filter to positive gain). After you
have found it, you can use the Inv button to cancel it
out.
Band 1 Freq
(20 to 2000 Hz)
Sets the frequency of the low band.
Band 1 Q-Factor
(0.5 to 10)
Controls the width or resonance of the low band.
Band 1
Filter mode
For the low band, you can select between three types
of shelving filters, a Peak (band-pass), and a Cut (low-
pass/high-pass) filter. When Cut mode is selected,
the Gain parameter is fixed.
-Shelf I adds resonance in the opposite gain direction
slightly above the set frequency.
-Shelf II adds resonance in the gain direction at the
set frequency.
-Shelf III is a combination of Shelf I and II.
Band 2 Gain
(-20 to +24 dB)
Sets the amount of cut/boost for the mid 1 band.
Band 2 Inv button Inverts the gain value of the filter (see the description
of the Invert button for Band 1).
Band 2 Freq
(20 to 20000 Hz)
Sets the center frequency of the mid 1 band.
Band 2 Q-Factor
(0.5 to 10)
Sets the width of the mid 1 band: the higher this value,
the “narrower” the bandwidth.
Band 3 Gain
(-20 to +24 dB)
Sets the amount of cut/boost for the mid 2 band.
Band 3 Inv button Inverts the gain value of the filter (see the description
of the Invert button for Band 1).
Band 3 Freq
(20 to 20000 Hz)
Sets the center frequency of the mid 2 band.
Band 3 Q-Factor
(0.5 to 10)
Sets the width of the mid 2 band: the higher this value,
the “narrower” the bandwidth.
Band 4 Inv button Inverts the gain value of the filter (see the description
of the Invert button for Band 1).
Band 4 Gain
(-20 to +24 dB)
Sets the amount of cut/boost for the high band.
Band 4 Freq
(200 to 20000 Hz)
Sets the frequency of the high band.
Band 4 Q-Factor
(0.5 to 10)
Controls the width or resonance of the high band.
Band 4
Filter mode
For the high band, you can select between three types
of shelving filters, a Peak, and a Cut filter. When Cut
mode is selected, the Gain parameter is fixed.
-Shelf I adds resonance in the opposite gain direction
slightly below the set frequency.
-Shelf II adds resonance in the gain direction at the
set frequency.
-Shelf III is a combination of Shelf I and II.
Output
(-24 to +24 dB)
This knob on the top right of the plug-in panel allows
you to adjust the overall output level.
Auto Gain button When this button is activated, the gain is automatically
adjusted, keeping the output level constant regardless
of the EQ settings.
Parameter Description
Position Sets the filter cutoff frequency. If you set this to a nega-
tive value, DualFilter will act as a low-pass filter. Positive
values cause DualFilter to act as a high-pass filter.
Resonance Sets the sound characteristic of the filter. With higher val-
ues, a ringing sound is heard.
Parameter Description