Plug-in Reference

84
The included VST Instruments
Mix
Filter
Envelope
LFO
X/Y Pad
Effects
Depth Controls the pitch modulation depth for the mod source
defined in the “mod src” field. The available range is +/-
one octave.
Mod Src Defines the pitch modulation source. Available sources
are: Modwheel, Aftertouch, Pitchbend, Velocity, LFO and
Mod Env.
PWM
(OSC2 only)
Controls the pulse width of the square wave. In the cen-
ter position, pulse width is 50/50. Turning the PWM knob
clockwise or counter clockwise creates a positive or neg-
ative pulse, respectively.
Sync
(OSC2 only)
Activating the sync button synchronizes the pitch of os-
cillator 2 to the pitch of oscillator 1. When this is active,
changing or modulating the pitch of oscillator 2 will
change the tone and not the pitch. For the typical sync
sound, turn osc 1 down in the mix and use osc 2 only.
Parameter Description
Osc 1 Sets the pre-filter level for oscillator 1.
Noise Sets the pre-filter noise level.
Osc 2 Sets the pre-filter level for oscillator 2.
Parameter Description
Mode Sets the filter type. Available filter types are 24 dB Low
pass, 18dB Low pass, 12dB Low pass, 6dB Low pass,
12dB Band pass and 12dB High pass.
Cutoff Sets the filter cutoff frequency. How this parameter oper-
ates is governed by the filter type.
High Pass Sets the cutoff frequency of the additional high-pass fil-
ter.
Res Changes the resonance of the multi-mode filter. Full res-
onance puts the filter into self-oscillation.
Key Track Determines the amount of key tracking applied to the fil-
ter cutoff frequency. The available range is 0 to 100%. A
range of 100% tunes the filter cutoff frequency to the
keyboards pitch 1:1.
Mod Src
(A+B)
Defines the filter modulation source. The available
sources are: Modwheel, Aftertouch, Pitchbend, Velocity,
LFO, and Mod Env.
Depth
(A+B)
Controls the filter modulation depth for the mod source
set in the “mod src” field.
Parameter Description
A – (Attack) Sets the attack time.
D – (Decay) Sets the decay time.
S – (Sustain) Sets the sustain level.
Parameter Description
R – (Release) Sets the release time.
Mod Src
(A+B)
Defines the envelope modulation source. You can select:
Modwheel, Aftertouch, Pitchbend, Velocity, LFO and
Mod Env.
Depth (A+B) Controls the envelope modulation depth for the mod
source defined in the “mod src” field.
Parameter Description
Waveform
(pop-up menu)
Here, you can select the waveform for the low frequency
oscillator. Available waveforms are: Triangle, Square,
Sawtooth, Sample & Hold and Random.
Rate Adjusts the frequency of the LFO, thus changing the rate
of the modulation. Depending on the LFO sync parame-
ter, you can edit the rate in Hertz or in note values.
Sync When “Sync” is “on” the LFO speed will be synchronized
to the sequencer’s tempo. This also affects the LFO rate
format.
Mod Src Defines the LFO modulation source. Available sources
are:
Modwheel, Aftertouch, Pitchbend, Velocity, LFO and
Mod Env.
Depth Controls the LFO modulation depth for the mod source
defined in the “mod src” field.
Parameter Description
X Par Sets the parameter to be modulated on the x axis of the
XY Pad. All of Monologue’s parameters are available as
destinations.
Y Par Sets the parameter to be modulated on the y axis of the
XY Pad.
XY Pad Use the mouse to control any two of Monologue’s param-
eters in combination. By moving the mouse horizontally,
you can control the x parameter, by moving it vertically,
you can control the y parameter. You can also record
controller movements as automation data.
Parameter Description
FX Type
(pop-up menu)
Selects the effect type for Monologue’s pitch effects. The
available types are Chorus, Flanger and Phaser.
Rate Use this to adjust the rate of the effect modulation.
Depth Use this to adjust the depth of the effect modulation.
FBK Controls the feedback of the effect.
Mix Controls the balance between dry and wet (effect) signal.
Set to 0, the effect will be off. Set to 50, the balance be-
tween dry and wet signal is 50/50.
Parameter Description